Honeywell Voyager 1400g Series Скачать руководство пользователя страница 75

Страница: 75 / 216

5 - 3

Other Programming Selections

Clear One Data Format

This deletes one data format for one symbology. If you are clearing the
primary format, scan

from the

Programming Chart

inside the back

cover of this manual. If you are clearing an alternate format, scan

, depending on the format you are clearing. Scan the Terminal Type

and Code I.D. (see

Symbology Charts

on page A-1), and the bar code

data length for the specific data format that you want to delete. All other
formats remain unaffected.

Clear all Data Formats

This clears all data formats.

Save

to exit and save your data format changes.

Discard

to exit without saving any data format changes.

Clear One Data Format

Clear All Data Formats

Save

Discard

Содержание Voyager 1400g Series

























































































































































































































Результаты поиска

Содержание Voyager 1400g Series

Отзывы:

Honeywell Voyager 1400g Series, Руководство пользователя, Страница: 75 / 216

Результаты поиска

Содержание Voyager 1400g Series

Отзывы: