Honeywell Voyager 1400g Series Скачать руководство пользователя страница 48

Страница: 48 / 216

2 - 24

the scanner waits for ACK/NAK again. Turn on the ACK/NAK protocol by
scanning the

ACK/NAK On

bar code below. To turn off the protocol, scan

ACK/NAK Off

Default = ACK/NAK Off

Scanner to Bioptic Communication

The following settings are used to set up communication between Honeywell
scanners and bioptic scanners.

Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout

must be set to 3000 in order to communicate with a bioptic scanner. See

RS232 Baud Rate

on page 2-20, and

RS232 Timeout

on page 2-23 for

further information.

Scanner-Bioptic Packet Mode

Packet Mode On

must be scanned to set the scanner’s format so it is com-

patible with a bioptic scanner.

Default = Packet Mode Off.

ACK/NAK On

* ACK/NAK Off

* Packet Mode Off

Packet Mode On

Содержание Voyager 1400g Series

























































































































































































































Результаты поиска

Содержание Voyager 1400g Series

Отзывы:

Honeywell Voyager 1400g Series, Руководство пользователя, Страница: 48 / 216

Результаты поиска

Содержание Voyager 1400g Series

Отзывы: