Honeywell Voyager 1400g Series Скачать руководство пользователя страница 156 | Manualshive

Страница: 156 / 216

Honeywell Voyager 1400g Series Скачать руководство пользователя страница 156

9 - 4

the Minimum Message Length (MIN) is set to 2 characters;
the Maximum Message Length (MAX) is set to 60 characters;
and the Default setting (DFT) has no value.

Resetting the Custom Defaults

If you want the custom default settings restored to your scanner, scan the

Acti-

vate Custom Defaults

bar code below. This resets the scanner to the custom

default settings. If there are no custom defaults, it will reset the scanner to the
factory default settings. Any settings that have not been specified through the
custom defaults will be defaulted to the factory default settings.

The charts on the following pages list the factory default settings for each of the
commands (indicated by an asterisk (*) on the programming pages).

Activate Custom Defaults

«
...
154
155
156
157
158
...
»

Содержание Voyager 1400g Series

























































































































































































































Отзывы:

Нет отзывов