background image

5

EN1R-9134 0503R20NE

Gas controls with external thread connection

WARNING

Fastening torque flat sealing ring only applicable for 
type Klingersil C4324

n

n

n

n

With

1

/

2

” nut and flat sealing ring for pipe 14 mm (see fig 5.)

Nut: drawing:......................................45.006.583-005
Flat sealing ring size: 

18 x 

10 x 1.5 mm:

drawing.......................................45.006.582-002

Fastening torque: maximum 40 Nm

minimum 25 Nm

Pipe end construction: see fig.: 8.

o

o

o

o

With 

1

/

2

” nut and flat sealing ring for pipe 15 mm (see fig 5.)

Nut: drawing:......................................45.006.583-004
Flat sealing ring size: 

18 x 

10 x 1.5 mm

drawing.......................................45.006.582-002

Fastening torque: maximum 40 Nm

minimum 25 Nm

Pipe end construction: see fig.: 9.

Fig. 5. External thread connection with nut and flat 

sealing ring

p

p

p

p

With 

3

/

4

” nut and olive (see fig. 6.)

Pipe diameter: 15 mm
Nut: drawing:......................................45.006.583-003
Fastening torque: maximum 50 Nm

minimum 30 Nm

Pipe end construction: square off end of tubing and 
remove burrs.

Fig. 6. External thread connection with nut and olive

q

q

q

q

With 

3

/

4

” nut and “O”-ring (see fig 7.)

Pipe diameter: 15 mm
Nut: drawing: ......................................45.006.583-003
“O”-ring size: 

14.3 x 

2.4 mm

drawing .......................................45.001.528-048

Fastening torque: maximum 50 Nm

minimum 10 Nm

Pipe end construction: see fig.: 10.

Fig. 7. External thread connection with nut and “O”-ring

r

r

r

r

With 

3

/

4

” nut and flat sealing ring for pipe 15 mm (see fig 5.)

Nut: drawing: ......................................45.006.583-003
Flat sealing ring size: 

24 x 

16 x 1.5 mm

drawing .......................................45.006.582-001

Fastening torque: maximum 50 Nm

minimum 30 Nm

Pipe end construction: see fig.: 11.

s

s

s

s

With 

3

/

4

” nut and flat sealing ring for pipe 18 mm (see fig 5.)

Nut: drawing: ......................................45.006.583-002
Flat sealing ring size: 

24 x 

16 x 1.5 mm

drawing .......................................45.006.582-001

Fastening torque: maximum 50 Nm

minimum 30 Nm

Pipe end construction: see fig.: 12.

Fig. 8. Pipe (dia 14 mm) for flat sealing ring connection

Fig. 9. Pipe (dia 15 mm) for flat sealing ring connection

Fig. 10. Pipe end for “O”-ring connection

1

14

18

+ 0.2
- 0.2

1

15

18

+ 0.2
- 0.2

1.5 – 0.1

15

23.4 – 0.15

15

7.5 – 0.2

+ 0.10
- 0.05

Содержание VK41 V Series









Отзывы: