manualshive.com logo in svg

Honeywell T8611G Chronotherm IV Deluxe, Руководство пользователя, Страница: 3 / 24

Поделиться
Скачать
Honeywell T8611G Chronotherm IV Deluxe Скачать руководство пользователя страница 3

T8611G CHRONOTHERM

® 

IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTAT

68-0165—1

3

Dimensions:
See Fig. 1.

Mounting Means:
The thermostat mounts on a wallplate. The wallplate mounts
horizontally on a wall or outlet box with two no. 6 x 32 screws
(included).

Accessories:

C7089B Outdoor Temperature Sensors (69-1020).
Universal Versaguard™ Thermostat guards.

RECYCLING NOTICE

If this control is replacing a control that contains
mercury in a sealed tube, do n

ot place your old

control in the trash.

Contact your local waste management authority for
instructions regarding recycling and the proper
disposal of the old thermostat.

INSTALLATION

When Installing this Product...

1. Read these instructions carefully. Failure to follow the

instructions can damage the product or cause a
hazardous condition.

2. Check the ratings given in the instructions and on the

product to make sure the product is suitable for your
application.

3. Installer must be a trained, experienced service

technician.

4. After completing installation, use these instructions to

check out the product operation.

Location

Install the thermostat about 5 ft (1.5m) above the floor in an
area with good air circulation at average temperature. See
Fig. 2.

Do not install the thermostat where it can be affected by:
—

drafts, or dead spots behind doors and in corners.

—

hot or cold air from ducts.

—

radiant heat from sun or appliances.

—

concealed pipes and chimneys.

—

unheated (uncooled) areas such as an outside wall
behind the thermostat.

Fig. 1. Dimensions of thermostat in in. (mm).

6-1/16 (154)

1/2
(13)

1-9/16

(40)

3-3/4

(95)

3-1/2

(89)

1-13/16

(46)

3/8 (10)

2-3/4 (70)

3-5/8 (92)

M10359

Содержание T8611G Chronotherm IV Deluxe

























Отзывы:

Нет отзывов