Honeywell SmartPAC 2 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 522

Honeywell SmartPAC 2 Скачать руководство пользователя страница 77

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 55

Part 3 – Install and Wire WPC Options

Wiring Lockout Relay (Optional), next section

Wiring a Remote Reset Switch (Optional), next page

Wiring Operator Mode Outputs (Optional), page 56

Wiring Foot Switch (Optional), page 57

Installing One-hand Control (Optional) , page 58

Wiring Automatic Single Stroke/External Trip, page 62

Wiring Continuous on Demand, page 62

Installing Multiple Operator Stations, page 63

Auxiliary Outputs (Optional), page 64

Wire a Keylock Switch to Prevent Changes to WPC Settings in Program and Run (Optional),
page 66

Installing Flywheel Speed Sensor (Optional Hardware Required), page 67

Mounting and Wiring the Bar Control Enclosure (Optional) , page 68

NOTICE

HIGH SPEED OPTION FOR SMARTPAC 2 WITH WPC

To set up the High Speed option for SmartPAC 2 with WPC, see “Set Up High Speed
Version of SmartPAC 2 with WPC,” page 94

Wiring Lockout Relay (Optional)

The lockout function in WPC provides an added safety feature to the product. Whenever a
serious error condition occurs, a lockout warning message appears on the SmartPAC 2
display alerting you of a problem. To clear a lockout condition, turn the STROKE SELECT
key switch toward “OFF” and then back to the desired operating mode.
To wire this relay to the WPC power supply board, refer to the wiring schematics at the end
of this manual (Figure 4 for Herion DSV or Figure 6 for Ross). Note that the relay can be
wired to critical press functions, such as the motor starter (see Figure 7 for an example).

«
...
75
76
77
78
79
...
»

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов