manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 90 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 90

1126800 

SmartPAC 2 with WPC Integration

Page 68

Chapter 2

Installing SmartPAC 2 and WPC

5. Run wires from the cam switch through flexible, liquid-tight conduit to WPC. WPC is

rated NEMA 12 (protected against dust and oil).  Therefore, you must use conduit rated
NEMA 12 and make proper conduit connections to ensure NEMA 12 protection.

6. Check your wiring.  You are done installing the LMCS and magnets.

Mounting and Wiring the Bar Control Enclosure
(Optional)

Whenever the press is in Bar mode, you will need to release the machine’s brake. Therefore,
mount the Bar Control enclosure in a place that is convenient to the operator while he is
barring the press.  

Make sure that the operator will not possibly block a light curtain while

pressing the BAR control operate button.

Refer to Figure 2 - 17 for dimensions. See wiring diagram Figure 3 and Table A at the end of
the manual for pinouts.

6. 75

(17 .15 )

2 plac es

.312

(0.79)

4 places

7.5 (19.05)

4.00

(10.16)

SELECT

ON

 OFF

OPERATE

DA TA INSTRUMENTS

100 Discovery  W ay, ACTON, MA 01720 USA

®

BAR CONTROL

2.00

(5.08)

front view

xx.xx in

(xx.xx cm)

3.00

(7.62)

top view

Figure 2 - 17.  Bar Control Enclosure Mounting Dimensions

(Top and Front Views)

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов