Honeywell S9361A207 Series Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 16

Honeywell S9361A207 Series Скачать руководство пользователя страница 9

S9361A207X INTEGRATED BOILER CONTROLLERS

9

69-2751—05

Temperature Control

Temperature control setpoint on the module can be
adjusted as described in the following sections. Some
modules with temperature control also include a
three-digit display on the printed circuit board to
facilitate adjustments and troubleshooting.

A separate automatic gas shutoff device is not
required in a system that uses this control to meet
requirements for CSA International ANSI Z21.87 and
UL 353.

The overall range of the setpoint is model-dependent
but is within 140°F to 220°F (60°C to 104°C) with a
default to 180°F (82°C). Select devices may have
different ranges.

Adjusting Settings for Models
with “On-Board” Display

To discourage unauthorized changing of settings, a
procedure to enter the adjustment mode is required.
To enter the adjustment mode, press the UP, DOWN,

and

I

buttons (see Fig. 1) simultaneously for three

seconds. Press and release the

I

button until the

parameter requiring adjustment is displayed.

Display

In the RUN mode, status items and parameters are
viewable. For example, to display setpoint, the control
will flash “SP” (setpoint) followed by the temperature
(i.e., 135), followed by °F or °C.

To read settings, press and release the I key to find the
parameter of interest. For example, press and release

I

until setpoint (SP) is displayed, followed by a three-
digit number, i.e., 220, followed by °F or °C. Pressing
the

I

button again will display the (bt) Boiler

Temperature followed by a three-digit number and the
corresponding degree designator. See Display
Readout.

Integrated Boiler Control One
Rod (Combined Ignitor and
Sensor) Model Displays

See Table 6–8 for the IBC display screens.

Wait for vent
damper to open

18

Damper actuator is energized and the system waits for damper to close

Wait for vent
damper to close

19

Damper actuator is de-energize and the system waits for damper to open

Wait for vent
damper to open –
failed closed

20

Damper actuator is energized, system waits for damper to open, but the damper is
stuck in closed position (damper end switch is open)

Wait for vent
damper to close –
failed open

21

Damper actuator is de-energized, system waits for damper to close, but the damper
is stuck in open position (damper end switch is closed)

Table 5. State Code Definitions. (Continued)

State

State

code

Specific Description

General

Description

Table 6. 7-Segment LED Display - Installer Mode Options.

3-Digit 7-Segment Display

Default

Range

Description

1st

Screen

2nd Screen

3rd

Screen

HL_

<High Limit>

°

F

or

°

C

180

140 to 220 °F

Adjust High Limit Setting

HdF

<High Limit Differential>

°

F

or

°

C

15

10 to 30 °F

Adjust High Limit Differential

Or_

<Pump Overrun Time>

0

0 to 10 minutes

Pump Overrun Time (minutes)

PP_

<Pump Pre-purge Time>

2

2 to 20 minutes

Pump Pre-purge Time (minutes)

St_

<Start Temperature>

°

F

or

°

C

140

140 to 180 °F

Start Temperature

Pt_

On

or

OFF

On

On

or

OFF

Priority Time on or off

dh_

dh

or

tt2

dh

dh

or

tt2

Select the domestic input as a
second heating zone. Note that the
text of parameter value is right-
adjusted, unlike the rest of the
parameters.

rSt

On

or

OFF

NA

NA

Reset Hard or Soft Lockout

F-C

°

F

or °

C

F

F or C

Select degrees F or C Mode

«
...
7
8
9
10
11
...
»

Содержание S9361A207 Series

















Отзывы:

Нет отзывов