Honeywell ms2420 Скачать руководство пользователя страница 36

Страница: 36 / 88

Changing the Wake Area Sensitivity Level (Photocell LED Range Adjust)

The MS2400 Series bar code scanner wake area sensitivity level can be set to the end users preference by
scanning one of the Photocell Sensitivity adjustment bar codes below.

*Max Photocell

Sensitivity

This feature enables the MS24xx to be at max
sensitivity or far sensing for the wake up photo
transistor.

* This is the default setting.

³ 2 2 1 2 0 0

Medium Photocell

Sensitivity

This feature enables the MS24xx to be at a
medium 1 sensitivity or medium sensing for
the wake up photo transistor.

³ 2 2 1 2 1 0

Low Photocell

Sensitivity

³ 2 2 1 2 2 0

This feature enables the MS24xx to be at a
low sensitivity or low sensing for the wake up
photo transistor.

Min Photocell

Sensitivity

³ 2 2 1 2 3 0

This feature enables the MS24xx to be at the
lowest sensitivity (close only) for the wake up
photo transistor.

MS2400 Series Bar Code Scanner Default Setting

Содержание ms2420

























































































Результаты поиска

Содержание ms2420

Отзывы:

Honeywell ms2420, Руководство пользователя, Страница: 36 / 88

Результаты поиска

Содержание ms2420

Отзывы: