Honeywell ms2420 Скачать руководство пользователя страница 12

Страница: 12 / 88

Scale Capacities

Capacity: kg unit

15 kg

lb. unit

30.0 lb.

Minimum Increment: kg unit

0.005 kg

lb. unit

0.01 lb.

Maximum Static

Weight:

kg unit

75 kg

lb. unit

150 lb.

Adjustments

required:

Calibration is required for scaled units.

Electrical

Voltage Supply: 2.5A @ +5V / 0.8A @ +12V

Operating Power: 11.2 Watts

Standby Power: 4.0 Watts

Operating Current: 1.7A @ 5.2V / 0.2A @ 12V

Standby Current: 0.6 A @ 5.2V / 0.07A @ 12V

DC Transformers: Class I; 5.2VDC @ 2.5A; 12VDC @ 0.8A

For Regulatory Compliance Information, refer to pages 69 - 71.

Environmental

Operating

Temperature:

0°C to 40°C (32°F to 104°F)

IP Rating: IP 55

Light Levels: 4842 Lux (450 footcandles)

Storage

Temperature:

-40°C to 60°C (-40°F to 140°F)

Humidity: 5% to 95% Relative Humidity, Non-Condensing

Contaminants: Sealed to resist airborne particulate contaminants.

Ventilation: None

Required

Specifications are subject to change without notice.

Содержание ms2420

























































































Результаты поиска

Содержание ms2420

Отзывы:

Honeywell ms2420, Руководство пользователя, Страница: 12 / 88

Результаты поиска

Содержание ms2420

Отзывы: