Honeywell MicroniK 200 R7426D Скачать руководство пользователя страница 10

Страница: 10 / 14

R7426D UNIVERSAL INPUT CONTROLLER

EN1B-0204GE51 R0403

Time Out

After approximately 10 min of inactivity (no button has been

pressed: time out) each mode returns automatically to

standard display mode. Inputs that have not been confirmed

by the

SET

button are ignored by the controller and old

parameter values will be retained.

Displaying Actual Values

In the standard display mode one of six actual values, can be

selected and displayed (Fig. 6) by pushing the

SEL

button.

The icons of the permanently displayed controller mode are

described in the following table:

Controller Mode / Status

Display

Off

Off - icon

Sun - icon

Main Input X1

Main Setpoint
CTRP1

Limitation / Cascade
Input X2

S ubmaster / Limit Setpoint
CTRP2

Compensation
Temperature T3

Output Y1

SEL

Fig. 6. Standard Display Mode

The output data (Y1) are displayed between the following ranges:

Output type

Control range

Output range

0...10Vdc

0...100%

0...120%

0...12V

(Dir)

-20...100%

12...0V

(Rev)

2...10Vdc

0...100%

-25...125%

0...12V

Содержание MicroniK 200 R7426D















Результаты поиска

Содержание MicroniK 200 R7426D

Отзывы:

Похожие инструкции для MicroniK 200 R7426D

Бренды по названию

Популярные бренды

Honeywell MicroniK 200 R7426D, Инструкции по установке и запуску

Результаты поиска

Содержание MicroniK 200 R7426D

Отзывы:

Похожие инструкции для MicroniK 200 R7426D

Бренды по названию

Популярные бренды