Honeywell IPC5000 Скачать руководство пользователя страница 51

Страница: 51 / 101

- 41 -

be highlighted if previous status was "STOP", and the program that is selected will
start to run.

STOP

: When the input of Digital input 1 is closed

(at the rising edge),

“STOP” status

will

be highlighted if previous status was "RUN", and the program that is selected will
stop running.

(1-2)

HOLD

: Terminal number is 3(DI2) and 1(DI_COM) of Digital input group.

When Digital input 2 is ON, it

holds the running program

and when it is OFF, it

continues to run the program

(1-3)

ADV

: Terminal number is 4(DI3) and 1(DI_COM) of Digital input group.

Each time Digital input 3 is ON, it

advances the processing

of a program by one

segment.

(2)

Channel Select

: Terminal number is 7(DI6), 8(DI7) and 1(DI_COM)

When Digital input 6 and/or 7 are ON, channels are selected other external remote
operations.

It is available for IPC5000D

They are chosen by the status of DI (See chart below)

DI6 DI7

Operation

Status

Enabled both CHANNEL (CH1, CH2)

CH1, 2 - ON

OFF

Enabled CH1, but disabled CH2

CH1 -
ON

OFF

Enabled CH2, but disabled CH1

CH2 -
ON

OFF

Disabled both CHANNEL (CH1, CH2)

CH1, 2 - OFF

Default

Disable

both channel Input (CH1, 2 is

OFF

)

(Note) When current Control mode is synchronous mode(Figure 3.17.1), if either of DI6

or DI7 is ON, the remote control of Digital inputs is available.

(3) TROUBLE Status Indication

Terminal of IPC5000D is

5(DI4), 6(DI5) and 1(DI_COM)

Terminal of IPC5000D is

5(DI4), 6(DI5), 7(DI6) and 1(DI_COM), 9(DI7) and 8(DI_COM)

When Digital

input 4 or 5 is ON

, The

trouble message

is displayed and operation mode of

the controller is changed to a trouble status. And Control output is 0.0% and all digital output is
OFF except digital output for TROUBLE. You can see the arrangement about Channel 1 or 2
of Digital input 4 and 5 on Table 2.6.2.

Refer the Section 3.18 for assigning Trouble Message.

(4) Program Number Selection

When current status is only STOP mode, the selection can be enabled.

Selection and indication are made according to the status of ‘DI’ below.

Содержание IPC5000






































































































Результаты поиска

Содержание IPC5000

Отзывы:

Похожие инструкции для IPC5000

Бренды по названию

Популярные бренды

Honeywell IPC5000, Руководство по установке

Результаты поиска

Содержание IPC5000

Отзывы:

Похожие инструкции для IPC5000

Бренды по названию

Популярные бренды