Honeywell HNDR-S4824 Скачать руководство пользователя страница 55

Страница: 55 / 80

Basic Configuration

HNDR-S4824

Honeywell

2004.05.31 (v 2.0)

DHCP can also be used for xDSL (PPPoE) interface. Sometimes, all computers on a Local Area Network

(LAN) share a single Floating / Dynamic IP address. In this case, the HNDR-S4824 should be assigned a

private IP address and have DHCP enabled. Users on the LAN can connect to the HNDR-S4824 using the

private IP address and outside users can connect to the HNDR-S4824 over the Internet.

IP Address, NetMask, and Gateway Address, DNS

Administrator may configure IP address, subnet mask, gateway address, and DNS addresses of HNDR-

S4824.

5.7.6.2. xDSL

If HNDR-S4824 is connected on xDSL line and needs PPPoE process, the network administrator

should configure the user ID and password for PPPoE. ID. The password may be acquired from the

ISP that installed the line. Once configured, the HNDR-S4824 will receive an IP address when it is

connected on xDSL line.

User ID/Password

When HNDR-S4824 is connected to xDSL, access ID and Password should be entered.

Status

Displays the HNDR-S4824 connection status.

Содержание HNDR-S4824

















































































Результаты поиска

Содержание HNDR-S4824

Отзывы:

Бренды по названию

Популярные бренды

Honeywell HNDR-S4824, Руководство пользователя

Результаты поиска

Содержание HNDR-S4824

Отзывы:

Бренды по названию

Популярные бренды