Honeywell HNDR-S4824 Скачать руководство пользователя

Страница: 13 / 80

Basic Configuration

HNDR-S4824

Honeywell

2004.05.31 (v 2.0)

3.4. Viewing all channels with sequence mode

There are two modes; basic sequence mode and user sequence mode. User sequence mode runs when

pressing the [SEQ] button during 1 second or above.

3.4.1. Basic sequence mode

- All channels can be viewed in successive order automatically using the [SEQ] button.

- Press the [MENU] button on the front panel to set-up the sequential cycle. (The default value is 3

seconds per channel for display.)

- Select “Monitor A” menu of “Monitor” tab among Configuration menus. And press the [ENTER] button.

- Select “Seq. Switching(sec)” and set any value between 1 and 60 seconds.

- In order to move to sequence mode from any viewer mode, press the [SEQ] button.

- In order to exit from sequence mode, press the [SEQ] button once again.

<Note>

Sequence mode can run only when connected and activated cameras are more than split screen. With

single full screen mode, activated cameras should be two or more. With quad-split screen mode, there

should be five or more activated cameras. In 16 / 13 spilit mode, sequence mode can’t be used.

Содержание HNDR-S4824

















































































Результаты поиска

Содержание HNDR-S4824

Отзывы:

Похожие инструкции для HNDR-S4824

Бренды по названию

Популярные бренды

Honeywell HNDR-S4824, Руководство пользователя

Результаты поиска

Содержание HNDR-S4824

Отзывы:

Похожие инструкции для HNDR-S4824

Бренды по названию

Популярные бренды