Honeywell Genesis 7580G Скачать руководство пользователя | Manualshive

Страница: 3 / 202

background image

Product Agency Compliance

USA

FCC Part 15 Subpart B Class B

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal-
lation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio or television technician for help.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions.
The user may find the following booklet helpful: “Something About Interference.” This is available at FCC local regional
offices.  Honeywell is not responsible for any radio or television interference caused by unauthorized modifications of this
equipment or the substitution or attachment of connecting cables and equipment other than those specified by Honeywell.
The correction is the responsibility of the user.

Use only shielded data cables with this system. This unit has been tested with cables less than 3 meters. Cables greater
than 3 meters may not meet class B performance.

Caution: Any changes or modifications made to this equipment not expressly approved by Honeywell may void the FCC
authorization to operate this equipment.

UL Statement

UL listed: UL60950-1, 2nd Edition.

Canada

Industry Canada ICES-003

This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Conformité à la règlementation canadienne

Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada. Son fonctionnement est assujetti
aux conditions suivantes :

1. Cet appareil ne doit pas causer de brouillage préjudiciable.

2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le brouillage pouvant causer un fonctionnement

indésirable.

C-UL Statement

C-UL listed: CSA C22.2 No.60950-1-07, 2nd Edition.

«
1
2
3
4
5
...
»

Содержание Genesis 7580G











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Genesis 7580G

Бренд: 3nStar Страницы: 51

Бренд: Datalogic Страницы: 184

Gryphon I GD4100

Бренд: Datalogic Страницы: 28

Magellan 2200VS

Бренд: Datalogic Страницы: 388

Gryphon I GD44XX

Бренд: Datalogic Страницы: 324

Бренд: Datalogic Страницы: 304

Gryphon 2D Series

Бренд: Datalogic Страницы: 356

Бренд: Datalogic Страницы: 208

Бренд: Datalogic Страницы: 18

Бренд: Datalogic Страницы: 16

Бренд: Datalogic Страницы: 12

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 48

Compact 2D Reader Matrix-2000

Бренд: Datalogic Страницы: 11

Бренд: Datalogic Страницы: 169

Бренд: Datalogic Страницы: 72

Бренд: Datalogic Страницы: 10

Gryphon I GD4100

Бренд: Datalogic Страницы: 428

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды