background image

LCD-SLP Product Installation Document —

 P/N LS10045-000GF-E:E  12/16/2019

17

Section 6: Programming Requirements

This product uses the CAMWorks™ Software Program. Installers must be Gamewell-FCI Factory Certified to program this 
product. For additional information on this product, contact the Gamewell-FCI Customer Support to schedule the Factory Certified 
Training.

LEDs

Display

Description

Release

Figure 5.2.5 Release LED Activated 

If the Releasing Zone is pre-programmed to use the Pre- 

Release Timer, after the Pre Release time  interval, the 

following occurs.
• The Release LED lights steady RED.
• Release appears on the display.
• The system activates the Release LED.
At this stage, the following occurs:
• The releasing output activates to open the valve.
• The valve releases the extinguishing agent.
• After the Cutoff Timer expires (if configured), the 

Release LED shuts off.

Cut Off

Figure 5.2.6 Cut Off LED Yellow 

Activated

If the Releasing Zone is pre-programmed to use the Cutoff 

Timer, after the Cutoff Timer interval, the following occurs:
• The system shuts off the solenoid.
• Cutoff appears on the display.
• All Releasing stage LEDs are OFF.

(See Note 1 in Table 5.2.1)

Squirt

Figure 5.2.7 Release LED Red 

Activated

If a user presses a Squirt switch, the following occurs:
• The Release LED temporarily changes to steady RED. 
• The releasing output is temporarily reactivated to open 

the valve.

• The System releases the extinguishing agent.
After the Squirt condition shuts off, the following occurs:

•  The Release LED turns off.

• The releasing output module closes the valves.

NOTES

Note 1: 

The Time Limit Cutoff delay may be programmed via CAMWorks.

Note 2: 

For additional information on how the Releasing application operates on the LCD-SLP, refer to the E3 Series Releasing 

Application Supplement, P/N:LS10138-151GF-E.

NOTE:

For information on the latest version of CAMWorks, see the Gamewell-FCI website, www.gamewell-fci-esd.com.

Table 5.2.1 LCD-SLP, Releasing Zone Screens

MENU

DRILL

RESET

AC

SILENCED

FIRE ALARM  HAZARD  SUPERVISORY  TROUBLE

STANDBY  PRE-ALRM  P-RELEASE  RELEASE   ABORT

MENU

DRILL

RESET

AC

SILENCED

FIRE ALARM  HAZARD  SUPERVISORY  TROUBLE

text

STANDBY   PRE-ALRM   P-RELEASE  RELEASE   ABORT

STANDBY  PRE-ALRM   P-RELEASE  RELEASE   SQUIRT

text

STANDBY  PRE-ALRM  P-RELEASE  RELEASE  ABORT

Содержание GAMEWELL LCD-SLP



















Отзывы: