Honeywell Dolphin 9900 страница 121 Скачать руководство пользователя

Страница: 121 / 170

Dolphin® Power Tools User’s Guide

Rev A

8/6/08

6 - 17

Sample SysInfo File

Field

Sample Data

This entry specifies the …

SYSTEM DATE/TIME

Date

1/14/2008

Date.

Time

10:38:36

Time.

SYSTEM INFO

Sample Data

This entry specifies the …

Hardware Revision

Hardware revision.

OS Version

WM60

Operating System version.

Kernel

22.06 (Dec 21, 2007)

Kernel version and date.

Service Pack

NONE

Service Pack level.

Boot Loader

0.00 ()

Bootloader version and date.

Keyboard Firmware

0.00

Keyboard firmware version.

Manufacture Date

20070711

Manufacture date.

Model Number

7600

Model number.

Part Number

7600EH-112-B4EE

Part number of the main board.

Special Part Number

7600EH-112-B4EE

Special part number, if any.

Terminal Serial Number

07193E0564

Terminal serial number.

CPLD Version

Unknown

CPLD firmware version.

Keyboard Type

29-key

Keyboard type.

Scanner Type

IT5300

Imager installed on the terminal.

Touch Panel Type

Installed

Touch panel type.

Display Type

Toppoly

Display type.

CPU INFO

Sample Data

This entry specifies the …

ProcessorName

S3C2440A

Name of the CPU

Architecture

ARM

Systems processor architecture.

ProcessorLevel

System’s architecture-dependent processor level.

Processor Frequency

400 Mhz

System’s processor operating frequency.

DLL VERSION INFO

Sample Data

This entry specifies the …

Decoder.dll

1.16.1.2

Current Decoder.dll api build revision.

Matrix Engine

4.84.1.11

Current Matrix engine build revision.

HHPScanInterface.dll

1.16

Current HHPScanInterface.dll api build revision.

Scan Driver

1.212.1.14

Current scan driver build revision.

HHPMT9V022HW.dll

1.00.02

Current HHPMT9V022HW.dll api build revision.

Содержание Dolphin 9900











































































































































































Результаты поиска

Содержание Dolphin 9900

Отзывы:

Похожие инструкции для Dolphin 9900

Бренды по названию

Популярные бренды

Honeywell Dolphin 9900, Руководство пользователя

Результаты поиска

Содержание Dolphin 9900

Отзывы:

Похожие инструкции для Dolphin 9900

Бренды по названию

Популярные бренды