manualshive.com logo in svg

Honeywell CR7075, Данные о продукции, Страница: 7 / 8

Поделиться
Скачать
Honeywell CR7075 Скачать руководство пользователя страница 7

CR7075 TWO-STAGE LIGHTING CONTROLLER

7

63-2180—1

CHECKOUT

In the following procedures, refer to the diagram inside the 

CR7075A cover or Fig. 3. These show locations of all 

operating controls, LED lights, and wiring connection points.

Initial Adjustments

1.

Adjust both light level potentiometers to the fully 

clockwise position (#1 index level).

2.

Place the SET-RUN switch to the RUN position.

Calibration

After the controller and photocell sensor are installed (with 

wiring and settings verified), and the photocell has been 

exposed to light for 16 hours, apply power. The light intensity 

threshold levels can be calibrated when the desired outdoor 

light level has occurred.

NOTES:

—

Calibration achieves best results when making 

adjustments at or near the light conditions 

required for switching the equipment.

—

Attempting calibration at extreme light conditions 

can cause switching to be unachievable.

1.

At the desired outdoor light level place SET-RUN switch 

to the SET position.

2.

Slowly rotate stage 1 light level potentiometer counter-

clockwise until the stage 1 LED lights.

3.

Stage 1 is now calibrated to the light level existing at the 

sensor and the stage 1 load is energized.

4.

Return the SET-RUN switch to the RUN position.

NOTE: To calibrate stage 2, repeat this process 

except adjust the stage 2 light level 

potentiometer.

IMPORTANT

After initial setup is complete, make certain the 

switch is in the RUN position to avoid short cycling 

the loads.

NOTE: The SET-RUN switch removes the integrating time 

delay (short-cycle protection) circuitry in the SET 

position. In the RUN position (normal operation) the 

calibrated light level must be present for 30 seconds 

before the load switches.

Содержание CR7075









Отзывы:

Нет отзывов