manualshive.com logo in svg

Honeywell CR7075, Данные о продукции, Страница: 3 / 8

Поделиться
Скачать
Honeywell CR7075 Скачать руководство пользователя страница 3

CR7075 TWO-STAGE LIGHTING CONTROLLER

3

63-2180—1

INSTALLATION

When Installing this Product...

1.

Read these instructions carefully. Failure to follow 

them could damage the product or cause a hazardous 

condition.

2.

Check the ratings given in the instructions and on the 

product to make sure the product is suitable for your 

application.

3.

Installer must be a trained, experienced service 

technician.

4.

After installation is complete, check out product 

operation as provided in these instructions.

CAUTION

Electrical Shock or Equipment Damage Hazard.

Can shock individuals or short equipment 

circuitry.

Disconnect power supply before installation.

Before Installation

IMPORTANT

Expose the photocell to light for 16 hours.

The photocells develop a hysteresis (or “light memory”) when 

packed for shipping. Until the photocell has been exposed to 

bright light for at least 16 hours, light level setpoints will shift.

Location

Locate the cadmium sulfide photocell sensor C7057A1000 

(supplied with this controller) so that the lens is exposed to full 

daylight. (See Fig. 2.)

NOTES:

—

Select an area which will not become shaded.

—

Mount 

only

 with light entrance facing horizontally.

—

Avoid overexposure to direct east/west sunlight.

Fig. 2. Vertical mounting configuration.

Mounting

IMPORTANT

Mount the photocell sensor to the top of a watertight, 

outdoor FS junction box.

1.

Use the gasket provided to prevent moisture entry.

2.

Screw stem into 1/2-14 threaded knockout.

NOTE: The photocell sensor can be mounted in a 

7/8 in. hole (or knockout).

Mount the controller on any convenient interior location:

1.

Remove the tamper-proof cover.

2.

Mount the controller using the two mounting holes 

provided in the metal enclosure corners (mounting 

screws not included).

NOTE: Use controller dimensions in Fig. 1 as a guide.

M20060

HEX NUT

LENS

PHOTOCELL

JUNCTION

BOX

GASKET

1/2-14 THREADED 

KNOCKOUT OR 

7/8 INCH HOLE

FOR BEST RESULTS, EXPOSE LENS 

TO LIGHT FROM THE NORTHERN SKY

(IN THE NORTHERN HEMISPHERE) 

OR THE SOUTHERN SKY (IN THE 

SOUTHERN HEMISPHERE).

USE WATERTIGHT JUNCTION BOX

WITH PROPER GASKETS AND SEALS.

1

2

2

1

Содержание CR7075









Отзывы:

Нет отзывов