Honeywell CP-700 Скачать руководство пользователя страница 23

Страница: 23 / 32

WEB-700 WEB-700-O CP-700

95-7776—01

WEB-700; WEB-700-O; CP-700

If after applying power, the STATUS LED goes out, or if the BEAT LED comes on (steady) and stays lit longer than 2 minutes,

contact your local distributor for technical assistance. See also “About LEDs” on page 24.

About the Backup Batteries

A WEB/CP-700 controller has two different backup batteries:

• An on-board NiMH battery pack, and

• An optional external, sealed lead-acid, rechargeable backup battery (or batteries). See below.

For continuous system operation during loss of primary power (to the NPB-PWR-UN-H module powering the unit), unless power

loss is only a few seconds, both batteries should be installed. Station alarms are generated if either battery is uncharged or

unable to hold a sufficient charge, as well as whenever primary power is lost. You should always investigate any alarm related to

backup batteries.

NiMH battery pack

A custom 10-cell NiMH (nickel metal hydride) battery pack is installed inside the WEB/CP-700, mounted atop the shield, and is

secured by a metal bracket and two kep nuts. This battery allows the controller to continue station operation (only) through very

short power bumps, meaning a few seconds in duration. In the case of a longer outage, the NiMH battery provides enough run

time for the unit to backup data and then shutdown. Typically, this process takes about one minute. Shutdown occurs

automatically, after data is backed up to on-board flash memory.

Upon startup (boot), a test of the NiMH battery is performed. A system alarm is generated if the NiMH battery voltage level is

found to be bad. A charge is also initiated upon startup, which lasts from 3 hours minimum, and can range up to 18 hours if the

battery is completely discharged. During this NiMH battery charge period, neither the NiMH battery or the external backup battery

is tested. After the startup NiMH charge period, a periodic test of

both

batteries occurs, and the appropriate battery alarm is

generated is either battery is found to be bad.

NOTE: If the last NiMH battery test was “bad,” upon loss of primary power the controller performs an immediate shutdown,

backing up data and powering off (including attached readers, and expansion modules).

A NiMH battery characteristic is to lose charge if not left in charge mode (trickle charge). Leaving the battery uncon-

nected, or the unit powered off, will cause the battery to fully discharge in a matter of weeks. Note that in the case of a

new controller, it ships from the factory with a completely discharged battery. Therefore, allow at least 18 hours for the

battery to charge after the controller is initially powered.

Replace the NiMH battery pack approximately every three years, or more often if the unit is in a high temperature environment.

For more information on the use and replacement of the battery, refer to Required NiMH Battery Maintenance, page 25.

BACKUP BATTERY

The optional sealed lead-acid backup battery (part number 712BNP) is an external, 12V, rechargeable battery (or multiple

batteries) sized to operate the system during loss of primary power, for some duration. This includes the controller, as well as

power to attached I/O expansion modules.

Connect the backup battery to the controller using a 2-position connector—see Fig. 11, page 21. Whenever primary-powered, the

controller supplies a constant “trickle” charge to this battery, at 200mA maximum. At startup (boot), a test of the backup battery is

performed, as well as a periodic test. A system alarm is generated if a battery test deems the backup battery to be bad.

Providing that the backup battery has tested good, upon loss of primary power the system operates from this backup battery

power until the charge level of the on-board NiMH battery pack reaches 0. Note that both batteries discharge in parallel. However,

as the sealed lead-acid backup battery capacity is much greater, the NiMH battery pack discharges much slower than if these

backup battery(ies) were bad or not present.

NOTE: If the backup battery test was “bad,” upon loss of primary power, the controller performs an immediate shutdown, back-

ing up data and powering off (including attached readers, expansion modules).

Replace the sealed lead-acid backup battery(ies) approximately every three years, or more often if the unit is in a high

temperature environment.

Содержание CP-700

































Результаты поиска

Содержание CP-700

Отзывы:

Похожие инструкции для CP-700

Бренды по названию

Популярные бренды

Honeywell CP-700, Руководство по установке

Результаты поиска

Содержание CP-700

Отзывы:

Похожие инструкции для CP-700

Бренды по названию

Популярные бренды