Honeywell BDR91T Скачать руководство пользователя страница 29

Страница: 29 / 34

Troubleshooting Guide

This is a quick guide to help you diagnose and cope with possible problems with

your wireless control system. For further assistance, please contact your Installer.

Symptom

Possible Cause

Remedy

ST9420C has a blank LCD

display

No power to the

heating system.

Check that there is power to the

heating system.

Fault in ST9420C

Call Installer

ST9420C indicates that

Heating and/or Hot Water

are

, but radiators are

cold and/or taps are running

with cold water.

Temperature controls

are switched off or

set too low.

Check that the temperature

controls in the system are set to

appropriate levels.

Boiler or other

system controls

have malfunctioned.

Call Installer

ST9420C shows the

message:

‘INTERNAL FAULT’

Fault in ST9420C

Call Installer

Every few seconds, the

ST9420C screen shows the

message:

ST9420C is

counting down the

number of days

until your next boiler

service is due.

Arrange a boiler service before

the counter reaches zero.

After servicing your boiler, the

Service Engineer / Installer will

reset the ST9420C to remind

you when the next boiler service

is due. Each service is normally

a maximum of 1 year apart.

Although the heating is still

operating, the ST9420C

screen keeps flashing the

message:

Your boiler service

overdue

Arrange an immediate boiler

service.

After servicing your boiler, the

Service Engineer / Installer will

reset the ST9420C to remind

you when the next boiler service

is due. Each service is normally

a maximum of 1 year apart.

Can I override the Programmer from the DT92E thermostat?

As well as changing the set temperature from the DT92E, it is also possible to override

the heating system on or off from the DT92E. This is only possible if the ST9420C is in

AUTO or ONCE Modes. If ST9420C is in CONT mode it will not be possible to switch

the heating off from the DT92E. Similarly, if ST9420C is in OFF mode, it will not be

possible to switch the heating on from the DT92E. If these latter overrides are required

it is first necessary to change the ST9420C mode setting to AUTO or ONCE.

FAQ AND TROUBLESHOOTING

Содержание BDR91T



































Результаты поиска

Содержание BDR91T

Отзывы:

Похожие инструкции для BDR91T

Бренды по названию

Популярные бренды

Honeywell BDR91T, Руководство пользователя

Результаты поиска

Содержание BDR91T

Отзывы:

Похожие инструкции для BDR91T

Бренды по названию

Популярные бренды