Honeywell AM-1 Series Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 12

Honeywell AM-1 Series Скачать руководство пользователя страница 2

AM-1 SERIES™

62-3075EFS—06

2

Fig. 1. AM-1 Series ASSE 1017 application. Dimensions

shown in in (mm).

Installation of Union Sweat, CPVC,
Union Propress and PEX
Connections

—

Union sweat connections, if used, should be sol-
dered prior to assembly to the valve, or without the
sealing gasket or optional check valve present.
After the joint has cooled, the sealing gasket
and/or check valves may be installed.

—

CPVC fittings are limited to a system maximum
temperature of 180° F (82° C) and 100 psi
(689 kPa).

—

PEX fitting and crimp ring (provided by Installer)
are deigned to meet ASTM F1807 requirements.

—

PEX tubing used with PEX fittings must meet
ASTM F876 requirements.

—

Press connections, use press tools and installation
practices compatible with Viega systems.

Installation of Temperature Gauge
Adapter

IMPORTANT

Union sweat connections must be soldered before
the thermowell with O-ring and sealing gasket are
installed. Install the thermowell with O-ring and
sealing gasket after the joint has cooled.

1.

Install thermowell with O-ring to the thermometer
adapter body.

2.

Tighten to 75 LB-IN ± 10 LB-IN.

DO NOT OVER-

TIGHTEN.

3.

Install the thermometer into the thermowell until
seated and tighten the set screw to secure in place.

Fig. 2. Temperature gauge installation.

VALVE ADJUSTMENT

To adjust temperature setting of the mixing valve, attach
thermostrip (supplied with the valve) to the piping
connected to the Mix port of the valve. Loosen handwheel
screw, lift handwheel and turn to desired temperature as
indicated on the thermostrip. Reposition the hand wheel
and retighten screw.

Temperature Setting Procedure

It is possible to limit the temperature range. To use this
feature:

M25029A

(1)

T

(1)

HEAT

TRAP

6

(152)

8

(203)

MAX

WATER

HEATER

EXPANSION

TANK

ALLOWABLE

SERVICE

VALVE

LOCATION

AM SERIES

WATER USE FIXTURES

RECIRCULATION

PUMP

M

COLD

WATER

SUPPLY

C

V

H

TO DISHWASHER

IF PERMITTED

BY CODES

T

AQUASTAT

(1) CHECK VALVE

GASKET

THERMOMETER

ADAPTER WITH

UNION NUT

O-RING

SCREW

THERMOWELL

THERMOMETER

M36644

M27487

LOOSEN SCREW, LIFT HAND WHEEL.

TURN HAND WHEEL CLOCKWISE

OR COUNTER CLOCKWISE TO

ADJUST TEMPERATURE.

1

2

REPOSITION HAND WHEEL

TO LOCK POSITION.

RETIGHTEN SCREW.

3

4

3

3

4

1

2

2

c

H

c

H

«
1
2
3
4
...
»

Содержание AM-1 Series













Отзывы:

Нет отзывов