Honeywell ADEMCO VISTA-48A, Инструкция по установке и настройке

Страница: 67 / 80

Follow-Me Feature
This feature lets users enter up to three phone numbers (system-wide) that the system will call in the
event of an alarm in any partition at the protected premises, thus alerting the user to the alarm.
•
When an alarm occurs, the system reports the alarm to the central station (and pagers, if programmed), then, if
programmed, dials the first follow-me phone number and proceeds as follows:
1. After dialing, the system waits a short time
†
then sends a series of eight tones or “beeps” (regardless of
whether the call is answered) followed by a pause of about four seconds, then the tones are repeated. The
cycle of tones and pauses continues for about one minute.
†
system waits about one ring plus any programmed pauses; see “To enter a follow-me number” below for
programming pauses
2. If the call is not acknowledged by the user (by pressing the telephone’s [
∗
] key; see User Response below),
the control hangs up when the 1-minute tone cycle is complete, then dials the second follow-me phone
number and sends the tones as described above. If the second number is not acknowledged by the user, the
control dials the third number and sends the tones.
3. If the third number is not acknowledged, the control redials the first number. This dialing cycle is repeated up
to three times or until a user acknowledges the call (presses the telephone’s [
∗
] key).
4. User Response:
a. When the call is answered, the user will hear the message tones (a series of eight tones or “beeps”)
followed by a pause of about four seconds, then the tones are repeated.
b. The user must press the [
∗∗∗∗
] key on the telephone to acknowledge hearing the tones, then wait for
the control to disconnect the line before hanging up.
IMPORTANT: The [
∗
] key should be pressed during a pause between tone cycles. Otherwise, the control
may not “hear” or respond to the [
∗
] key if pressed while the tones are being sent.
•
If another alarm occurs in the same armed period, the Follow-Me dialing cycle is repeated only up to the
number of reports programmed in field *93 No. of Reports in Armed Period per Zone.
•
If the follow-me number is for a pager, the message displayed on the pager is as follows: 104 P ZZZ
where “P” is the partition number, “ZZZ” is the 3-digit zone number of the zone in alarm.
To enter a Follow-Me phone number: user code + [#] + [6] [1]
The first follow-me phone number (if it exists) is displayed:
FM Phone No.
18009216704--_
To display follow-me phone number 2, press [2].
To display follow-me phone number 3, press [3].
•
To modify the displayed number, do the following:
1. Press [
∗
], which clears the number, then enter the desired phone number. To include a 2-second pause in
the number, press [#] at the point in the entry the pause is desired (it displays as “–“). Pauses entered at
the end of the number will allow dialing but will delay the message tones by the amount of pause
programmed.
2. Press [
∗
] to save the new number. The next follow-me phone number in sequential order (1-2-3-1 etc.) is
displayed. Press [
∗
] to program that number, or press [1], [2], or [3] to select the desired follow-me number
to be programmed.
Setting/Adjusting the Real-Time Clock
The real-time clock is used to time-stamp events recorded in the event log and for scheduling mode. The time
display can be set for 12 (AM/PM) or 24-hour format, and can show day/month or month/day (field *183,
Time/Date Format). If the system is using the built-in crystal for the real-time clock (field *181, 50/60Hz AC
Operation) synchronization, a plus/minus adjustment may be required to account for crystal frequency
variation. This adjustment is only needed if the frequency control of AC mains is not accurately maintained by
the local mains electrical power provider.
To set and adjust the clock: user code +[#] + [6] [3]. The current setting is displayed.
Press [
∗
] to set the time. A cursor appears under the first digit of the hour.
•
Enter the 2-digit hour setting, then enter the 2-digit minute setting.
•
Press [1] for PM or [0] for AM (if applicable, otherwise skip).
•
Enter the last two digits of the current year, the 2-digit month setting, then the 2-digit day setting.
•
Press [
∗
] to accept the settings and continue.
The Clock Adjustment prompt is displayed.
•
Press [0] to add, or press [1] to subtract.
•
Enter the number of seconds per day (01-59) to add or subtract to keep the real-time clock accurate.
•
Press [
∗
] to accept the setting and exit.
6-7