Honeywell 2RM7800L1087 Скачать руководство пользователя страница 15

Страница: 15 / 32

RM7800L1087; RM7840G1022,L1075; EC7840L1014 RELAY MODULES WITH VALVE PROVING

66-1162—2

Fig. 16. Select/Restart screen.

11.

Press down arrow to select.

12.

“

Getting Data

” will be momentarily displayed, followed

by the screen shown in Fig. 12.

Changing the Installed Postpurge

Fig. 17. Setting Postpurge time.

This screen allows for setting up the Postpurge for the

RM7800L/40G,L, EC7840L. This will be the time that the

Combustion Fan (terminal 5) will remain energized after the

demand ends.

NOTE: The device comes standard with 15-second Post-

purge.

13.

Use the +/- buttons to adjust the postpurge time.

Time changes:

0 to 60 seconds in 1-second intervals.

60 to 600 seconds in 10-second intervals.

10 to 60 minutes in 1-minute intervals.

14.

Press Enter (Left/Right arrow keys simultaneously)

when the correct postpurge time is displayed.

Fig. 18. Save Changes screen.

15.

Use the down arrow to save changes. “

Getting Data

” is

displayed momentarily.

The following steps are to confirm your selections.

Fig. 19. Confirmation Acknowledgement screen. (The

Valve Proving Test location is shown.)

16.

Press ENTER.

Fig. 20. Confirmation Correct screen.

17.

Use the down arrow to confirm correct.

NOTE: Using the up arrow during this step will take you back

to the beginning of the setup routine.

“

Getting Data

” will be displayed.

Fig. 21. Confirm screen.

18.

Press Enter.

Fig. 22. Confirm Correct screen.

19.

Use the down arrow to confirm correct.

“

Getting Data

” will be displayed.

The following steps are used to confirm your selection.

=Select
=Restart

M22764B

BACK

ENTER

Edit:

M22668

BACK

ENTER

Edit:

SETUP:Postpurge
±PostTime: 00:30

=Save changes
=Restart

M22665B

BACK

ENTER

Edit:

CONFIRM:ValvProve
±VP When: BEFORE ?

M22670B

BACK

ENTER

Edit:

=Confirm correct
=Incorrect

M22671B

BACK

ENTER

Edit:

CONFIRM: ValveProve
VP Time: 00:30 ?

M22672A

BACK

ENTER

Edit:

=Confirm correct
=Incorrect

M22671B

BACK

ENTER

Edit:

Содержание 2RM7800L1087

































Результаты поиска

Содержание 2RM7800L1087

Отзывы:

Похожие инструкции для 2RM7800L1087

Бренды по названию

Популярные бренды

Honeywell 2RM7800L1087, Руководство по установке

Результаты поиска

Содержание 2RM7800L1087

Отзывы:

Похожие инструкции для 2RM7800L1087

Бренды по названию

Популярные бренды