Honeywell 104484A Скачать руководство пользователя

Страница: 11 / 16

IMMERSION WELLS AND COMPRESSION FITTINGS

68-0040—04

Fig. 11. Mounting sensing bulb and

311266D Bulb Holder in duct.

NOTE: Dimensions shown in in. (mm).

Duct Mounting with Capillary Compression

Fitting

In some duct-mount application, it is desirable to use a

compression fitting to reduce air leakage at the sensing

element location. For these applications, first mount a waste

nut on the duct to ensure secure mounting. See Fig. 12. See

Table 6 for part numbers.

NOTE: Do not use this mounting method for liquid

applications.

Fig. 12. Mounting sensing bulb in duct using waste nut

and compression fitting.

Averaging Element Holders

The averaging element must be supported so it is distributed

evenly across the entire height and width of the duct. It can be

fastened to perforated strap iron (see Fig. 13) or mounted with

314439 Mounting Clips (see Fig. 14). This type of mounting

requires threading the element through a grommet inserted in

a hole in the duct wall.

For ducts with limited access, the 7640HX Averaging Element

Mounting Kit allows mounting the element through a single

hole in the side of the duct. This kit requires a length of 1/2 in.

EMT conduit. See Fig. 15.

Fig. 13. Mounting averaging element with

perforated strap iron.

Fig. 14. Mounting averaging element with

314439 Mounting Clips.

Fig. 15. Mounting averaging element with 7640HX

Averaging Element Mounting Kit.

14 (356)

3-1/4
(83)

1-3/8
(35)

1-5/8
(41)

3-1/4
(83)

2-3/4
(70)

2-1/4 x 2-1/4 (57 x 57) APPROXIMATE
HOLE IN DUCT FOR INSTALLATION

ADJUSTABLE

SPRING
CLIPS (2)

THERMOMETER
BULB

ACCESS
HOLE

RUBBER GROMET

NO. 8 SHEET METAL
MOUNTING SCREWS (2)

CONTROLLER BULB

M7355

CAPILLARY

COMPRESSION

FITTING

CAPILLARY
TUBING

DUCT
WALL

WASTE
NUT

BULB
(CAPSULE)

M17266

DUCT
WALL

WIRE FASTENINGS

CAPILLARY
TUBING

GROMMET

ELEMENT

M17269

DUCT
WALL

CAPILLARY
TUBING

GROMMET

AVERAGING
ELEMENT

USE NO. 10
SHEETMETAL
SCREWS

314439
CLIP

BEND HERE
IF NECESSARY

M17289

DUCT
WALL

4 in.
COVER
PLATE

CAPILLARY

GROMMET

AVERAGING
ELEMENT

M17270

CONDUIT
COMPRESSION
FITTING

WIRE TIES

1/2 in. EMT CONDUIT
(OBTAIN LOCALLY)

Содержание 104484A

















Результаты поиска

Содержание 104484A

Отзывы:

Похожие инструкции для 104484A

Бренды по названию

Популярные бренды

Honeywell 104484A, Данные о продукции

Результаты поиска

Содержание 104484A

Отзывы:

Похожие инструкции для 104484A

Бренды по названию

Популярные бренды