PILOT SCREW
BOLTS
SUPPORT BRACKET
THROTTLE STOP SCREW
XL2 0 0
4-14
NOTE
Install the fuel tank support bracket and tighten the bolts.
Perform the following adjustment:
– Throttle grip free play
– Idle speed adjustment
• After installation, turn the fuel valve ON, and check that
there is no fuel leaks.
PILOT SCREW ADJUSTMENT
IDLE DROP PROCEDURE
NOTE
1. Turn the pilot screw clockwise until it seats lightly and then
back it out to the specification.
Initial opening: 1 3/8 turns out (2LA) 1-3/4 turns out (DK).
h
2. Warm up the engine to operating temperature.
3. Stop the engine and connect the tachometer according to
the tachometer manufacturer’s operating instructions.
4. Start the engine and adjust the idle speed with the throttle
stop screw.
Idle speed: 1.400 ± 100 min
-1
(rpm).
• Damaged the pilot screw seat will occur if the screw is
tightened against the seat.
• The pilot screw is factory pre-set and not adjustment can be
done unless it is replaced.
• The engine must be warm for accurate adjustment. Then
minutes of stop-and-go riding is sufficient.
• Use a tachometer with graduations of 50 min
-1
(rpm) or
smaller that will accurately indicate a 50 min
-1
(rpm)
change.
FUEL SYSTEM
LOW ALTITUDE SETTING (2LA type only)
When the vehicle is to be operated continuously below
1,000 m (3,300 feet) the carburetor must be readjusted
as following specifications.
MAIN JET: # 115
JET NEEDLE CLIP POSITION:
3rd groove from
top
LOW ALTITUDE SETTING:
3/8 turn in from
standard setting.
Содержание XL200 2001
