Honda MSX GROM 2020 Скачать руководство пользователя страница 73

Страница: 73 / 102

Adjusting the Clutch Lever

Freeplay

Upper Adjustment

Attempt adjustment with the upper clutch

cable adjuster first.

Pull back the rubber dust cover.

Loosen the upper lock nut.

Turn the upper clutch cable adjuster until

the freeplay is 10 - 20 mm (0.4 - 0.8 in).

Tighten the upper lock nut and check the

freeplay again.

Reinstall the rubber dust cover.

Lower Adjustment

If the upper clutch cable adjuster is threaded

out near its limit, or the correct freeplay

cannot be obtained, attempt adjustment with

the lower clutch cable adjusting nut.

20200817160140_32K26J100_eng_BOOK Page 71 Monday, August 17 2020 16:04:26 JST

Clutch

Adjusting the Clutch Lever Freeplay

Maintenance

Upper clutch cable adjuster

Upper lock nut

Rubber dust cover

–

Содержание MSX GROM 2020







































































































Результаты поиска

Содержание MSX GROM 2020

Отзывы:

Похожие инструкции для MSX GROM 2020

Бренды по названию

Популярные бренды

Honda MSX GROM 2020, Руководство пользователя

Результаты поиска

Содержание MSX GROM 2020

Отзывы:

Похожие инструкции для MSX GROM 2020

Бренды по названию

Популярные бренды