Honda MSX GROM 2020 Скачать руководство пользователя страница 28

Страница: 28 / 102

Average speed [AVG]

Displays the average speed since the selected

tripmeter was reset.

The average speed will be calculated based on

value displayed on the tripmeter (A or B)

selected.

Also, the average speed for tripmeter A will be

displayed when the odometer and tripmeter A

are selected.

Display range: 0 to 199 km/h

•

Initial display: “---” is displayed.

•

When your vehicle has traveled less than 0.2

km since the engine was started: “---” is

displayed.

•

When your vehicle operating time is less

than about 30 seconds since the engine was

started: “---” is displayed.

When “---” is displayed except for the above-

mentioned cases, go to your dealer for service.

To reset the average speed:

(

P.20

)

20200817160140_32K26J100_eng_BOOK Page 26 Monday, August 17 2020 16:04:26 JST

Operation Guide

Continued

Содержание MSX GROM 2020







































































































Результаты поиска

Содержание MSX GROM 2020

Отзывы:

Похожие инструкции для MSX GROM 2020

Бренды по названию

Популярные бренды

Honda MSX GROM 2020, Руководство пользователя

Результаты поиска

Содержание MSX GROM 2020

Отзывы:

Похожие инструкции для MSX GROM 2020

Бренды по названию

Популярные бренды