Honda GCV520 Скачать руководство пользователя страница 45

Страница: 45 / 60

＋

−

＋

−

＋

−

＋

TECHNICAL & CONSUMER INFORMATION

Battery Connections for Electric Starter

NEGATIVE (

)

BATTERY CABLE

POSITIVE (

)

BATTERY CABLE

STARTER SOLENOID

Be careful not to connect the battery in reverse polarity, as this will
short circuit the battery charging system. Always connect the positive
(

) battery cable to the battery terminal before connecting the

negative (

) battery cable, so your tools cannot cause a short circuit if

they touch a grounded part while tightening the positive (

) battery

cable end.

Use a 12-volt battery with an ampere-hour rating of at least 45 Ah.

A battery can explode if you do not
follow the correct procedure,
seriously injuring anyone nearby.

Keep all sparks, open flames, and
smoking materials away from the
battery.

Connect the battery positive (

) cable to the starter solenoid

terminal as shown.

Connect the battery negative (

) cable to an engine mounting bolt,

frame bolt, or other good engine ground connection.

Connect the battery positive (

) cable to the battery positive (

)

terminal as shown.

Connect the battery negative (

) cable to the battery negative (

)

terminal as shown.

Coat the terminals and cable ends with dielectric grease.

03/05/14 17:16:31 31Z0A600_044

Содержание GCV520





























































Результаты поиска

Содержание GCV520

Отзывы:

Похожие инструкции для GCV520

Бренды по названию

Популярные бренды

Honda GCV520, Руководство пользователя

Результаты поиска

Содержание GCV520

Отзывы:

Похожие инструкции для GCV520

Бренды по названию

Популярные бренды