Honda GCV520 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 60

background image

39

HELPFUL TIPS & SUGGESTIONS

Removal From Storage

Position the equipment so the engine is level. Tilting can cause fuel or
oil leakage.

With the engine and exhaust system cool, cover the engine to keep out
dust. A hot engine and exhaust system can ignite or melt some
materials. Do not use sheet plastic as a dust cover. A nonporous cover
will trap moisture around the engine, promoting rust and corrosion.

Remove the battery and store it in a cool, dry place. Recharge the
battery once a month while the engine is in storage. This will help to
extend the service life of the battery.

Check your engine as described in the

BEFORE OPERATION

chapter of

this manual.

If the fuel was drained during storage preparation, fill the tank with
fresh gasoline. If you keep a container of gasoline for refueling, be
sure that it contains only fresh gasoline. Gasoline oxidizes and
deteriorates over time, causing hard starting.

If the cylinders were coated with oil during storage preparation, the
engine may smoke briefly at startup. This is normal.

03/05/14 17:15:59 31Z0A600_040

«
...
39
40
41
42
43
...
»

Содержание GCV520





























































Отзывы:

Нет отзывов

Похожие инструкции для GCV520

Бренд: Rato Страницы: 65

PRESTIGE PS2.60FA

Бренд: CAB Страницы: 16

Бренд: Continental Motors Страницы: 146

Бренд: Jiecang Страницы: 2

Бренд: SOMFY Страницы: 7

Бренд: YOODA Страницы: 7

Бренд: Evolution Technologies Страницы: 12

Lombardini SILEO 1000

Бренд: Kohler Страницы: 168

Бренд: Yamaha Страницы: 51

Бренд: Daewoo Страницы: 165

Бренд: Chevrolet Страницы: 17

Бренд: Honda Страницы: 65

Бренд: Cub Cadet Страницы: 40

Бренд: SKY Engines Страницы: 34

Бренд: Traxxas Страницы: 40

Бренд: Lenze Страницы: 52

Бренд: KaVo Страницы: 12

Бренд: Bartec Varnost Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды