Honda Eu7000is Скачать руководство пользователя страница 44

Страница: 44 / 49

EU-127

Date Revised: March 2021 (PSV52522-S)
© 1998-2021 American Honda Motor Co., Inc.—All Rights Reserved

EU Mo

dels

STATOR INSPECTION

Remove the inverter unit.
Pull the recoil starter and measure the voltage between the terminals of the
generator 3P connectors (

and

) with the generator mounted.

• After generator voltage inspection, reset the error log.

If the output voltage is less than the standard voltage. Measure the resistance between the terminals of the generator 3P connectors
(

and

) according to the table below.

If the resistance is out of the specification, check the stator coil resistance

according to the table below.

If all resistances are OK, replace or repair the generator wire harness.
If the resistance is out of specification, replace the stator.

Generator

Connector

Terminal number

Specific voltage

Master

1 - 2

AC 15 V or more

2 - 3

1 - 3

Slave

1 - 2

AC 15 V or more

2 - 3

1 - 3

Generator

Connector

Terminal number

Standard resistance

Master

1 - 2

0.44 - 0.62

2 - 3

1 - 3

Slave

1 - 2

0.44 - 0.62

2 - 3

1 - 3

Stator

Terminal

number

Standard

resistance

Master

N 1 - U 1

0.22 - 0.31

N 1 - V 1

N 1 - W 1

Slave

N 2 - U 2

0.22 - 0.31

N 2 - V 2

N 2 - W 2

N 2

N 1

V 2

W 1

V 1

W 2

U 2

U 1

Содержание Eu7000is

















































Результаты поиска

Содержание Eu7000is

Отзывы:

Бренды по названию

Популярные бренды

Honda Eu7000is, Руководство пользователя

Результаты поиска

Содержание Eu7000is

Отзывы:

Бренды по названию

Популярные бренды