Honda EM10000 Скачать руководство пользователя страница 58

Страница: 58 / 86

＋

−

SERVICING YOUR GENERATOR

Battery Charging

Battery Installation

The battery gives off explosive
hydrogen gas during normal
operation.

A spark or flame can cause the
battery to explode with enough
force to kill or seriously hurt you.

Wear protective clothing and a face
shield, or have a skilled mechanic
perform the battery maintenance.

Connect the battery charger following the manufacturer’s
instructions.
Charge the battery.
Clean the outside of the battery and the battery compartment with a
solution of baking soda and water.

Install the battery into the generator.
Connect the battery positive (

) cable to the battery positive (

)

terminal first, and tighten the bolt securely.
Slide the battery boot over the positive (

) cable and terminal.

Connect the battery negative (

) cable to the battery negative (

)

terminal, and tighten the bolt securely.

The battery is rated at 28.0 Ah (ampere hours). Charging current
should equal 10% of the battery’s ampere hour rating.

2.
3.

1.
2.

3.
4.

11/12/06 12:58:41 42Z26700_058

Содержание EM10000























































































Результаты поиска

Содержание EM10000

Отзывы:

Похожие инструкции для EM10000

Бренды по названию

Популярные бренды

Honda EM10000, Руководство пользователя

Результаты поиска

Содержание EM10000

Отзывы:

Похожие инструкции для EM10000

Бренды по названию

Популярные бренды