Honda CRF125F 2022 Скачать руководство пользователя страница 51

Страница: 51 / 132

FEATURES
(Not required for operation)

LEFT SIDE COVER

The left side cover (1) must be removed for air
cleaner and sub fuse maintenance.

Removal:

1. Remove the bolt A (2), bolt B (3) and collar

(4).

2. Pull out the prong (5) from the rubber

grommet (6), and the boss (7) from the hole
(8) on the shroud.

Installation:
1. Hook the tab (9) to the shroud and slide the

top of the side cover under the bottom edge
of the seat.

2. Align the prong with the rubber grommet,

and also the boss with the hole on the
shroud.

3. Install the collar onto the bolt B.
4. Install the bolt B and bolt A and tighten

them securely.

(1) Left side cover
(2) Bolt A
(3) Bolt B
(4) Collar
(5) Prong

(6) Grommet
(7) Boss
(8) Hole
(9) Tab

(4)

(3)

(1)

(2)

(9)

(7)

(5)

(8)

(6)

Содержание CRF125F 2022





































































































































Результаты поиска

Содержание CRF125F 2022

Отзывы:

Бренды по названию

Популярные бренды

Honda CRF125F 2022, Руководство пользователя

Результаты поиска

Содержание CRF125F 2022

Отзывы:

Бренды по названию

Популярные бренды