Honda CRF125F 2022 Скачать руководство пользователя страница 34

Страница: 34 / 132

MAJOR COMPONENTS

(Information you need to operate this motorcycle)

BRAKES
Front Brake

This motorcycle has a hydraulic front disc

brake.

As the brake pads wear, brake fluid level drops.

There are no adjustments to perform, but fluid

level and pad wear must be inspected

periodically. The system must be inspected

frequently to ensure there are no fluid leaks. If

the brake lever free travel becomes excessive

and the brake pads are not worn beyond the

recommended limit (page 86), there is probably

air in the brake system and it must be bled. See

your dealer for this

service.

Brake Fluid Level:

With the motorcycle in an upright position,

check the fluid level. It should be above the

LWR mark (1). If the level is at or below the

LWR mark, check the brake pads for wear

(page 86).

Worn pads should be replaced. If the pads are

not worn, have your brake system

inspected for leaks.

The recommended brake fluid is Honda DOT 3

or DOT 4 brake fluid from a sealed container,

or an equivalent.

(1) LWR mark

(1)

Содержание CRF125F 2022





































































































































Результаты поиска

Содержание CRF125F 2022

Отзывы:

Бренды по названию

Популярные бренды

Honda CRF125F 2022, Руководство пользователя

Результаты поиска

Содержание CRF125F 2022

Отзывы:

Бренды по названию

Популярные бренды