Honda CRF125F 2022 Скачать руководство пользователя страница 48

Страница: 48 / 132

Wheel & Tyre Replacement

The tyres that came on your motorcycle were
designed to match the performance capabilities
of your motorcycle and provide the best
combination of handling, braking, durability
and comfort.

Used tyres should not be installed if the

previous usage record is unknown.

The recommended tyres for your motorcycle

are:

Front: CRF125F: 70/100-17M/C 40M

CRF125FB: 70/100-19M/C 42M

Rear:

CRF125F: 90/100-14M/C 49M

CRF125FB: 90/100-16M/C 51M

Type: bias-ply, tube

The recommended wheels for your motorcycle

are:

Front: CRF125F: 17 × 1.4

CRF125FB: 19 × 1.4

Rear:

CRF125F: 14 × 1.85

CRF125FB: 16 × 1.85

Whenever you replace a tyre, use one that is

equivalent to the original and be sure the wheel

is balanced after the new tyre is installed.

Also remember to replace the inner tube

whenever you replace a tyre. The old tube will

probably be stretched, and if installed in a new

tyre, it could fail.

Installing improper tyres on your

motorcycle can affect handling and

stability. This can cause a crash in

which you can be seriously hurt or

killed.

Always use the size and type of tyres

recommended in this owner’s manual.

Содержание CRF125F 2022





































































































































Результаты поиска

Содержание CRF125F 2022

Отзывы:

Бренды по названию

Популярные бренды

Honda CRF125F 2022, Руководство пользователя

Результаты поиска

Содержание CRF125F 2022

Отзывы:

Бренды по названию

Популярные бренды