Honda CBR 2018 Series Скачать руководство пользователя страница 79

Страница: 79 / 140

Turn both adjusting nuts an equal

number of turns until the correct drive

chain slack is obtained. Turn the adjusting

nuts clockwise to tighten the chain. Turn

the adjusting nuts counterclockwise and

push the rear wheel toward the front to

provide more slack.

Adjust the slack at a point midway

between the drive sprocket and the

driven sprocket.

Check the drive chain slack.

P. 73

Check rear axle alignment by making sure

the chain adjuster index marks align with

the front edge of the adjusting slots.

Both marks should correspond. If the axle

is misaligned, turn the right or left

adjusting nut until the marks are aligned

and recheck chain slack.

Tighten the rear axle nut.

Torque:

65 lbf·ft (88 N·m, 9.0 kgf·m)

Tighten the drive chain adjusting nuts

lightly, then hold the adjusting nuts and

tighten the lock nuts.

Torque:

15 lbf·ft (21 N·m, 2.1 kgf·m)

Recheck drive chain slack.

If a torque wrench was not used for

installation, see your dealer as soon as

possible to verify proper assembly.

Improper assembly may lead to loss of

braking capacity.

20170925135210_31K75A200_enu_BOOK Page 78 Monday, September 25 2017 13:58:25 JST

Drive Chain

Adjusting the Drive Chain Slack

Maintenance

Continued

Содержание CBR 2018 Series













































































































































Результаты поиска

Содержание CBR 2018 Series

Отзывы:

Похожие инструкции для CBR 2018 Series

Бренды по названию

Популярные бренды

Honda CBR 2018 Series, Руководство пользователя

Результаты поиска

Содержание CBR 2018 Series

Отзывы:

Похожие инструкции для CBR 2018 Series

Бренды по названию

Популярные бренды