Honda CBR 2018 Series Скачать руководство пользователя страница 77

Страница: 77 / 140

Drive Chain

Inspecting the Drive Chain

Slack

Check the drive chain slack at several points

along the chain. If the slack is not constant at

all points, some links may be kinked and

binding.

Have the chain inspected by your dealer.

Shift the transmission to Neutral. Stop the

engine.

Place your motorcycle on its side stand on

a firm, level surface.

Check the slack in the lower half of the

drive chain midway between the

sprockets.

Drive chain slack:

13/16 - 1 3/16 in (20 - 30 mm)

Do not ride your motorcycle if the

slack exceeds 1 15/16 in (50 mm).

Roll the motorcycle forward and check

that the chain moves smoothly.

20170925135210_31K75A200_enu_BOOK Page 76 Monday, September 25 2017 13:58:25 JST

Maintenance

Continued

Содержание CBR 2018 Series













































































































































Результаты поиска

Содержание CBR 2018 Series

Отзывы:

Похожие инструкции для CBR 2018 Series

Бренды по названию

Популярные бренды

Honda CBR 2018 Series, Руководство пользователя

Результаты поиска

Содержание CBR 2018 Series

Отзывы:

Похожие инструкции для CBR 2018 Series

Бренды по названию

Популярные бренды