Homelite UT13130 Скачать руководство пользователя

Страница: 6 / 20

120693

eleCTRIC CHAIN SAW

For more information, visit www.desatech.com

Mounting

Stand-Outs

Guide Bar

Bolts

Guide Bar

Nuts

Adjusting

Hole

Guide

Bar

Tapping

Screw

Saw

Chain

Cutting

Edge

Cutting

Edge

Towards

Guide

Bar Nose

Front Hand

Guard

Drive

Sprocket

Figure 3 - Assembling Guide Bar, Chain, and Hand Guard

Adjusting

Plate

Adjusting

Screw

Sprocket

Support

Figure 4 - Part Locations For Assembling Guide Bar

Adjusting

Block

ASSeMBlY

The plastic hardware bag should include:
•  two guide bar bolts
•  two guide bar nuts
•  one Phillips-head tapping screw
•  automatic  chain  sharpener  (Fast  Sharp

models only)

1. Lay chain out ﬂat.
2. Install front hand guard onto saw body.

Do this by pressing two mounting stand-

outs on hand guard into hex-shaped

holes in saw body (see Figure 3).

3 Insert tapping screw through hand

guard and into saw handle. Tighten

screw ﬁrmly.

4. Turn adjusting screw counterclockwise

(see Figure 4). Continue to turn adjust-

ing screw until adjusting block is to rear

of adjusting plate.

5. Install guide bar onto saw body. Place

rear of guide bar between adjusting

plate and sprocket support.

IMPORTANT:

Make sure to insert

adjusting block into oval adjusting hole

on guide bar.

6. Line up holes on sprocket support with

center slot on guide bar and holes in

saw body.

7. Insert guide bar bolts through front

hand guard, saw body, center slot of

guide bar, and sprocket support. Attach

guide bar nuts to guide bar bolts.

IMPORTANT:

Tighten guide bar nuts

ﬁnger tight only. Make sure adjusting

block is in oval adjusting hole on guide

bar.

8. Place chain around drive sprocket,

then along top groove of guide bar and

around guide bar nose.

Note:

Make

sure cutting edges of chain are facing

the right direction. Position chain so

cutting edges on top of guide bar face

guide bar nose (see Figure 3).

Note:

Some models are pre assembled. As-

sembly is not needed on these models.
See

Saw Chain Tension Adjustment

, page 7.

WARNING: Cutting edges on

chain are sharp. Use protective

gloves when handling chain.

IMPORTANT: Do not clamp chain

saw in vise during assembly.

CAUTION: Do not place chain

on saw backwards. If chain is

backwards, saw will vibrate badly

and will not cut.

9. Adjust saw chain tension. Follow steps

under

Saw Chain Tension Adjustment,

page 7.

Содержание UT13130





















Результаты поиска

Содержание UT13130

Отзывы:

Похожие инструкции для UT13130

Бренды по названию

Популярные бренды

Homelite UT13130, Руководство пользователя

Результаты поиска

Содержание UT13130

Отзывы:

Похожие инструкции для UT13130

Бренды по названию

Популярные бренды