background image

Page 34 

WARRANTY

LIMITED WARRANTY STATEMENT

Homelite Consumer Products, Inc. warrants to the original 
retail purchaser that this 

HOMELITE product is free from 

defect in material and workmanship and agrees to repair or 
replace, at Homelite Consumer Products, Inc.’s discretion, 
any  defective  product  free  of  charge  within  these  time 
periods from the date of purchase.

�  One year for the following units: Yard Broom, Trimlite 

and Bandit;

�  Two years if the product is used for personal, family or 

household use;

  90  days,  if  used  for  any  other  purpose,  such  as 

commercial or rental.

This  warranty  extends  to  the  original  retail  purchaser 
only  and  commences  on  the  date  of  the  original  retail 
purchase.
Any  part  of  the 

HOMELITE  product  manufactured  or 

supplied  by 

HOMELITE  and  found  in  the  reasonable 

judgment  of 

HOMELITE  to  be  defective  in  material  or 

workmanship will be repaired or replaced by an authorized 
HOMELITE service dealer without charge for parts and 
labor. 
The product, including any defective part, must be returned 
to an authorized service dealer within the warranty period. 
The expense of delivering the 

HOMELITE product to the 

dealer for warranty work and the expense of returning it 
back to the owner after repair or replacement will be paid by 
the owner. 

HOMELITE’S responsibility in respect to claims 

is limited to making the required repairs or replacements 
and  no  claim  of  breach  of  warranty  shall  be  cause  for 
cancellation or rescission of the contract of sale of any 
HOMELITE product. Proof of purchase will be required by 
the dealer to substantiate any warranty claim. All warranty 
work  must  be  performed  by  an  authorized 

HOMELITE 

service dealer. 
This warranty is limited to ninety (90) days from the date 
of original retail purchase for any 

HOMELITE product that 

is used for rental or commercial purposes, or any other 
income-producing purpose.
This  warranty  does  not  cover  any 

HOMELITE  product 

that has been subject to misuse, neglect, negligence, or 
accident, or that has been operated in any way contrary 
to the operating instructions as specified in this

 operator’s 

manual. This warranty does not apply to any damage to 
the 

HOMELITE  product  that  is  the  result  of  improper 

maintenance  or  to  any 

HOMELITE  product  that  has 

been altered or modified. The warranty does not extend 
to repairs made necessary by normal wear or by the use 
of parts or accessories which are either 

INCOMPATIBLE 

WITH  THE  HOMELITE  product  or  adversely  affect  its 
operation, performance, or durability.

In addition, this warranty does not cover:
A.  Tune-ups  –  Spark  Plugs,  Carburetor,  Carburetor 

Adjustments, Ignition, Filters

B.  Wear items – Bump Knobs, Outer Spools, Cutting Lines, 

Inner Reels, Starter Pulleys, Starter Ropes, Drive Belts, 
Tines, Felt Washers, Hitch Pins, Mulching Blades, Blower 
Fans, Blower and Vacuum Tubes, Vacuum Bags and 
Straps, Guide Bars, Saw Chains

HOMELITE reserves the right to change or improve the 
design  of  any 

HOMELITE  product  without  assuming 

any  obligation  to  modify  any  product  previously 
manufactured.
ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION 
TO THE STATED WARRANTY PERIOD. ACCORDINGLY, 
ANY  SUCH  IMPLIED  WARRANTIES  INCLUDING 
MERCHANTABILITY,  FITNESS  FOR  A  PARTICULAR 
PURPOSE,  OR  OTHERWISE,  ARE  DISCLAIMED  IN 
THEIR  ENTIRETY  AFTER  THE  EXPIRATION  OF  THE 
APPROPRIATE TWO-YEAR, ONE-YEAR, OR NINETY DAY 
WARRANTY PERIOD. HOMELITE’S OBLIGATION UNDER 
THIS  WARRANTY  IS  STRICTLY  AND  EXCLUSIVELY 
LIMITED  TO  THE  REPAIR  OR  REPLACEMENT  OF 
DEFECTIVE PARTS AND HOMELITE DOES NOT ASSUME 
OR AUTHORIZE ANYONE TO ASSUME FOR THEM ANY 
OTHER OBLIGATION. SOME STATES DO NOT ALLOW 
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY 
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY 
TO  YOU.  HOMELITE  ASSUMES  NO  RESPONSIBILITY 
FOR  INCIDENTAL,  CONSEQUENTIAL,  OR  OTHER 
DAMAGES INCLUDING, BUT NOT LIMITED TO, EXPENSE 
OF  RETURNING  THE  HOMELITE  PRODUCT  TO  AN 
AUTHORIZED  SERVICE  DEALER  AND  EXPENSE  OF 
DELIVERING IT BACK TO THE OWNER, MECHANIC’S 
TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES, 
RENTAL  OF  A  LIKE  PRODUCT  DURING  THE  TIME 
WARRANTY SERVICE IS BEING PERFORMED, TRAVEL, 
LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS 
OF REVENUE, LOSS OF USE OF THE PRODUCT, LOSS 
OF  TIME,  OR  INCONVENIENCE.  SOME  STATES  DO 
NOT  ALLOW  THE  EXCLUSION  OR  LIMITATION  OF 
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE 
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY 
TO YOU.
This warranty gives you specific legal rights, and you may 
also have other rights which vary from state to state.
This  warranty  applies  to  all 

HOMELITE  products 

manufactured  by 

HOMELITE  and  sold  in  the  United 

States and Canada.
To locate your nearest service dealer, dial 1-800-242-4672 
or log on to our website at www.homelite.com.

Содержание UT10532 - OPERATORS







































Отзывы: