Homelite UT10532 - OPERATORS Скачать руководство пользователя

Страница: 29 / 38

Page 29

MAINTENANCE

ADJUSTING THE CARBURETOR

See Figures 64 - 66.

Before adjusting the carburetor:



Use a brush or compressed air to clean the starter cover
vents.



Clean the air filter. Refer to

Cleaning the Air Filter in the

Maintenance

section of this manual.



Allow the engine to warm up prior to adjustment of engine
idle speed.

WARNING:

Weather conditions and altitude may affect carburetion.
Do not allow bystanders close to the chain saw while
adjusting the carburetor.

Idle Speed Adjustment —The idle speed adjustment controls
how much the throttle valve stays open when the throttle
trigger is released. To adjust:



Turn idle speed screw

“T” clockwise to increase idle

speed.



Turn idle speed screw

“T” counterclockwise to decrease

idle speed.

WARNING:

THE SAW CHAIN SHOULD NEVER TURN AT IDLE.
Serious personal injury may result from the saw chain
turning at idle.

CLEANING THE STARTER UNIT

See Figure 65.

Use a brush or compressed air to keep the cooling vents of
the starter assembly free and clean of debris.

Fig. 66

AIR FILTER

STARTER COVER

VENTS

Fig. 65

Fig. 64

IDLE

SPEED

SCREW

“T”

Содержание UT10532 - OPERATORS







































Результаты поиска

Содержание UT10532 - OPERATORS

Отзывы:

Похожие инструкции для UT10532 - OPERATORS

Бренды по названию

Популярные бренды

Homelite UT10532 - OPERATORS, Руководство оператора

Результаты поиска

Содержание UT10532 - OPERATORS

Отзывы:

Похожие инструкции для UT10532 - OPERATORS

Бренды по названию

Популярные бренды