background image

90-OM1863-P3

90-OM1863-P2

3

2

Problem

Suggested Remedy

Possible Cause

1. Lights will not switch on at 

dusk.

No power.

Ensure transformer is plugged in 
and power is switched on.

2. Only some of the lights 

switch on at dusk.

Terminal spikes in the light power 
connector have not made contact 
with the core of the cable.

Straighten the terminal spikes and 
reattach the power connector to 
the low voltage lighting cable.

Low voltage cable has not been 
connected to the transformer.

Ensure the low voltage cable is 
connected to the transformer.

Artificial light affecting the 
sensor e.g. street lights.

Mount the sensor where the 
artificial lights will not affect the 
sensor.

Lamp not correctly fitted into the 
lampholder.

Ensure the lamp is correctly 
fitted.

The lamp has blown.

Replace the lamp.

Trouble Shooting :

8 CM

Mounting Slots

Kit Contents :

AMLS-30

  

4  Tier Lights  
4  Threaded Cap  
4  Inserts  
4  Ground Spikes  
5  12W 12V Lamps  
1  96W Transformer  
15m approx. Cable   

Installation

1. Locate the transformer in a suitable position, 

considering that the transformer has to be 
plugged in indoors.

2. Unwind and lay out the cable to its full length 

along the line where the tier lights will be 
positioned, starting at the position where the 
transformer is to be located.

Assembly of Lights :

1. Screw the post on to the head, ensuring the 

post is fully tightened.

2. Attach the ground spike, ensuring the cable is 

positioned in the slot.

3. Repeat for the remaining lights.
4. At the point where you 

want to locate the Tier 
lights, attach the Tier 
light power connector by 
the following method.  
Place the plastic insert in 
the wiring channel, 
aligning the holes with 
the terminal spikes.  Lay 
the cable in the plastic 
insert so that the 
terminal spikes align with 
the centre of each core 
of the cable.  Whilst 
holding the cable in place, 
screw on the threaded 
cap.  The cap will force 

the terminal spikes to pierce the cable, holding 
it in place.

5. Repeat for the remaining Tier lights.

Ensure you have followed all of the steps 
above and the Tier lights are fully assembled 
and connected to the low voltage cable 
before connecting the low voltage cable to 
the transformer.

Transformer Installation :

1. The recommended transformer mounting 

location is a minimum of 30cm above the 
ground and located where its power cord is 
within reach of a standard 230V power socket 
outlet located indoors, or a suitable 
weatherproof socket if used outdoors.

The transformer is equipped with a photo-cell 
which will automatically turn the lights on at 
dusk and off at dawn.  To accurately do this, 
the photo-cell must be mounted (using the 
screws provided) in an area where it will be 
exposed to the natural light of the rising and 
setting sun.  Avoid heavily shaded areas or 
areas where artificial light may shine onto the 
photo-cell.  Light from automobiles, 
streetlights, porch light, etc. may cause your 
lights to turn off prematurely.

Note : the photo-cell may be mounted 
horizontally or vertically.  If you chose to 
mount the transformer indoors, the photo-cell 
must be placed in a window.

2. You may hang the transformer indoors or 

outdoors on a wall, fence, post etc. by using 

the screws provided.  The screw locations are 
to be positioned so they will slide onto the 
slots on the rear of the transformer.

There are not user serviceable parts within the 
transformer.

Wiring Instructions:

1. Strip away 15mm of insulation off of both wires 

at one end only of the low voltage lighting 
cable.

2. Remove the terminal cover at the bottom of the 

transformer.  Loosen the two terminals and 
wrap one of the stripped wires around each 
terminal screw. Tighten the screw ensuring that 
all strands of the wire at captured under the 

terminal screw heads.  Replace the terminal 
cover.

Do not loop the low voltage lighting cable 
back to the transformer.

The transformer may now be plugged into an 
appropriate socket.  Please note the lights will 
not come on until dusk.  If you require the lights 
not to be operated by the photo-cell on the 
transformer, it may be wrapped in insulation 
tape to shut out the lights from the sensor.

Lamp Replacement

1. Switch off the power supply to the transformer 

and ensure the lamp is cool before handling.

2. Remove the three screws in the underside of 

the Tier light fitting head and remove the shade 
rings.

3. Unscrew the glass dome and remove.
4. Replace the lamp with a lamp of the same style 

and rating.

5. Re-assemble in reverse order.

Power

cord

Extension
Pipe

Light
Head

Stake

Отзывы: