manualshive.com logo in svg

HOMEDEPOT 19A30031100, Руководство оператора

Поделиться
Скачать
HOMEDEPOT 19A30031100 Скачать руководство пользователя страница 6

ASSEMBLY AND INSTALLATION

6

NOTE:

 

The clevis pin can be fed down through the hitch plate and secured underneath with 

the cotter pin, or it may be easier to feed the clevis pin up through the hitch plate hole and 
secure with the cotter pin on the topside. Insert the cotter pin into the top hole, closest to 
the head of the pin. You may need to push up on the pin to make the hole accessible.

IMPORTANT !

 If you decided to leave the 

hitch support only finger tight during the 
assembly process, tighten all of the 
hardware securely at this time.  
 

Mount Vertical  

Support Bracket

1. 

Install the vertical support bracket 
onto the mounting assembly on the 
tractor by hooking it over the cross 
mounting bracket. See Figure 5. 

2. 

Align the vertical support bracket 
with the hole that best suits the 
deck size of your tractor.

3. 

Secure the vertical support bracket 
to the cross mounting bracket using 
a carriage bolt (710-0276) and wing 
knob (720-04122) from hardware 
pack 689-02364. See Figure 6.

 

NOTE:

 

Position “C” is the recommended 

mounting position, but you may use other 
mounting positions to accommodate 
other attachments. 

Install Hanger Assembly

1. 

Install and secure hanger assembly 
onto the vertical support bracket 
using two carriage bolts (710-
0276), two cup washers (736-0242) 
and two lock nuts (712-04063) 
from hardware pack 689-02364. 
See Figure 7. 

Assembling Remaining 

Bagger Components

1. 

Tilt the front of the upper chute 
support slightly forward. Slide the 
clip behind the tab, then snap the 
front latch to the rail, as shown in 
(1) of Figure 8. 

2. 

Snap the upper chute support in 
place by first clipping the side 
portion onto the hanger assembly 
rail. See (2) in Figure 8. 

3. 

Slide the left grass catcher cover 
over the upper chute support and 
the hanger assembly rail. Carefully 
latch the two tabs in place into the 
front of the upper chute support, 
see (1) in Figure 9. 

4. 

Fit the snaps onto the left side 
hanger assembly rail. See (2) in 
Figure 9. 

Figure 6

Figure 7

1

2

Figure 8

2

1

1

Figure 9

NOTE: 

Before performing any of the instructions throughout this manual, references to left, 

right, front and rear of the tractor are from the operator’s position, unless otherwise stated.

• 

Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop 
the tractor engine and set the parking brake.

• 

For convenience, pivot the seat forward and leave it in that position until the grass 
collector is fully mounted and assembled. 

Assemble Mounting Brackets

To assemble the universal mounting 
assembly, locate the rider hitch bracket 
assembly (689-00304A) and the universal 
support bracket (783-08129) and follow 
these steps:
1. 

Attach the two hitch side brackets 
to the rear support bracket 
(rider hitch bracket assembly 
689-00304A) using two carriage 
bolts (710-0276) and wing knobs 
(720-04122) from hardware pack 
689-02364. See Figure 1.  

NOTE:

  

The hooks on the side 

brackets should point downwards 
and the tabs on the rear plate point 
upwards as shown in Figure 1.

2. 

Flip over assembly and mount the 
hitch support bracket to the 
universal support bracket (783-
08129) using two carriage bolts 
(710-0276) and wing knobs (720-
04122) from hardware pack 689-
02364. See Figure 2. 

NOTE:

 

It might be easier during the mounting stage to leave this hardware only finger tight 

to facilitate lining up the hitch hole for the clevis pin. You will be instructed to tighten this 
hardware later in this manual.

NOTE:

  

Use the two holes closest to the 

cross mount, see Figure 2. The hitch 
support bracket will need to be flipped to 
enable alignment of the proper holes.  
 

Mount Assembly on Tractor

1. 

Place the hooked ends of the 
mounting assembly over the 
shoulder bolts on the back of the 
tractor frame and line up the hitch 
support bracket center hole with 
the hole on the tractor’s hitch. See 
Figure 3. 

2. 

Install the clevis pin (711-0309A) 
from hardware pack 689-02364 
into the tractor’s hitch and secure 
with a cotter pin (714-0117). 
See Figure 4.

 

Figure 1

For All Other Models

Knob Hole Position

Figure 2

Figure 3

Align hole on

bracket with hole

on tractor

Figure 4

38” Deck

42” Deck

46” Deck

A B C

Figure 5

Содержание 19A30031100





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды