Holzstar 5902423 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 38

background image

Description of device

HBS Series | Version 1.02

9

5.1 Packaging

All of the machine‘s packaging materials and packing
aids are suitable for recycling and must always be dispo-
sed of using material-based recycling systems.

Packaging materials made of cardboard must be shred-
ded and disposed of as part of waste paper recycling.

The foils are made of polyethylene (PE), padding is
made of polystyrene (PS). Dispose of these substances
at a recycling centre or hand them over to the relevant
waste disposal company.

5.2 Storage

Store the Wood Band Saw thoroughly cleaned in a dry,
clean and frost-free environment. Cover the machine
with a protective plane.

6

Description of device

6.1 Machine

Illustrations in these operating instructions may de-
viate from the original.

HBS 231-1

Fig. 3: Wood Band Saw HBS 231-1

1 Handle

2 Handle screw saw blade tension

3 Saw blade guide

4 Star grip for locking the roller cover

5 Saw blade

6 Miter stop

7 Saw table

8 Angle adjustment screw

9 Star grip for locking the roller cover

10 Chip containers

11 Push stick

12 Clamping lever for rip fence

13 ON / OFF switch

14 LED light switches

WARNING!

Danger to life!

If the weight of the machine and the permissible load
capacity of the lifting equipment are not observed
during transport or lifting work, the machine may tip
over or fall.
- During transport and lifting operations, observe the

weight of the machine and the permissible load
capacity of the lifting equipment.

- Check that hoists and load handling attachments

are in a wall-free condition.

NOTE!

- The machine may only be loaded and unloaded by

qualified personnel.

- Never drive directly with the forks under the

machine to lift it!

NOTE!

- For transport, all covers must be attached to the

machine frame.

- The machine must not be rocked by the crane

during transport.

1

2

3

4

5

6

7

8
9

10

11

12

13

14

«
...
7
8
9
10
11
...
»

Содержание 5902423







































Отзывы:

Нет отзывов

Похожие инструкции для 5902423

Бренд: F.F. Group Страницы: 40

Бренд: Milwaukee Страницы: 32

Бренд: YATO Страницы: 128

Бренд: Kalamazoo Страницы: 6

Бренд: Titan Страницы: 16

Бренд: Sammic Страницы: 40

Бренд: MAKO TOOLS Страницы: 19

Бренд: Scheppach Страницы: 111

Бренд: Scheppach Страницы: 152

Бренд: Hitachi Страницы: 20

Бренд: Hitachi Страницы: 32

Бренд: Hitachi Страницы: 22

Бренд: Hitachi Страницы: 20

Бренд: Hitachi Страницы: 54

Бренд: Hitachi Страницы: 40

Бренд: Hitachi Страницы: 56

Бренд: Hitachi Страницы: 43

Бренд: Hitachi Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды