Holtek HT68FB240 Скачать руководство пользователя страница 111

Страница: 111 / 133

Rev. 1.10

110

November 26, 2019

Rev. 1.10

111

November 26, 2019

HT68FB240

USB Low Speed Flash MCU

Bit 4

SELUSB:

USB mode and V33O on/off select bit

0: not USB

mode,

turn-off V33O

1: USB

mode,

turn-on V33O

When the

V33C

bit is set high, the USB and V33O functions is selected and the pin-shared

pins, UDN/GPIO0 and UDP/GPIO1, will become the UDN and UDP pins for the USB.

SELUSB SELPS2

USB and PS2 mode description

1.No mode supported

2.V33O pin not output and it will floating

3.UDN/GPIO0 and UDP/GPIO1 pins cann’t output

1.PS2 mode

2.V33O pin output VDD

3.UDN/GPIO0 and UDP/GPIO1 pins will become the GPIO0 and

GPIO1 pins, which can output by firmware

1.USB mode

2.V33O output 3.3V

3.UDN/GPIO0 and UDP/GPIO1 pins will become the UDN and

UDP pins

x: don’t care

Bit 3

RESUME:

USB resume indication bit

0: SUSP bit goes to "0"

1: leave the suspend mode

When the USB leaves the suspend mode, this bit is set to "1" (set by SIE). When the

RESUME is set by SIE, an interrupt will be generated to wake-up the MCU. In order

to detect the suspend state, the MCU should set USBCKEN and clear SUSP2 (in the

UCC register) to enable the SIE detect function. RESUME will be cleared when the

SUSP goes to "0". When the MCU is detecting the SUSP, the condition of RESUME

(causes the MCU to wake-up) should be noted and taken into consideration.

Bit 2

URST:

USB reset indication bit

0: no USB reset

1: USB reset occurred

This bit is set/cleared by the USB SIE. This bit is used to detect a USB reset event on

the USB bus. When this bit is set to "1", this indicates that a USB reset has occurred

and that a USB interrupt will be initialized.

Bit 1

RMWK:

USB remote wake-up command

0: no remote wake-up

1: remote wake-up

It is set by MCU to leave the USB host leaving the suspend mode. Indicate that the

USB host leaves the suspend mode.

Bit 0

SUSP:

USB suspend indication

0: not in the suspend mode

1: enter the suspend mode

When this bit is set to 1 (set by SIE), it indicates that the USB bus has entered the

suspend mode. The USB interrupt is also triggered when this bit changes from low to

high.

Содержание HT68FB240






































































































































Результаты поиска

Содержание HT68FB240

Отзывы:

Похожие инструкции для HT68FB240

Бренды по названию

Популярные бренды

Holtek HT68FB240, Руководство пользователя

Результаты поиска

Содержание HT68FB240

Отзывы:

Похожие инструкции для HT68FB240

Бренды по названию

Популярные бренды