background image

                  

BA45F56xx Wireless Transceiver Application

 

 

AN0571EN V1.00 

14 / 14 

November 5, 2020 

Disclaimer 

All information, trademarks, logos, graphics, videos, audio clips, links and other items appearing 
on this website ('Information') are for reference only and is subject to change at any time without 
prior notice and at the discretion of Holtek Semiconductor Inc. and its related companies 
(hereinafter 'Holtek', 'the company', 'us', 'we' or 'our'). Whilst Holtek  endeavors to ensure the 
accuracy of the Information on this website, no express or implied warranty is given by Holtek to 
the accuracy of the Information. Holtek shall bear no responsibility for any incorrectness or leakage. 

Holtek shall not be liable for any damages (including but not limited to computer virus, system 
problems or data loss) whatsoever arising in using or in connection with the use of this website by 
any party. There may be links in this area, which allow you to visit the websites of other companies. 
These websites are not controlled by Holtek. Holtek will bear no responsibility and no guarantee to 
whatsoever Information displayed at such sites. Hyperlinks to other websites are at your own risk. 

Limitation of Liability 

In no event shall Holtek Limited be liable to any other party for any loss or damage whatsoever or 
howsoever caused directly or indirectly in connection with your access to or use of this website, the 
content thereon or any goods, materials or services. 

Governing Law 

This disclaimer is subjected to the laws of the Republic of China and under the jurisdiction of the 
Court of the Republic of China. 

Update of Disclaimer 

Holtek reserves the right to update the Disclaimer at any time with or without prior notice, all 
changes are effective immediately upon posting to the website. 

Содержание BA45F56 Series















Отзывы: