Holman MM14 Скачать руководство пользователя страница 7

 

PAGE 6 

OPERATOR'S MANUAL 

HOLMAN CONVEYOR BAKERS 

MODEL MM14

 

 

TROUBLESHOOTING GUIDE CONT.

 

 
C. 

HEAT LIMIT SWITCH 

 
 

Your Holman Conveyor Oven is equipped with an automatically activated HEAT LIMIT SWITCH   which 
interrupts the heater tube connections if the air temperature in the control box exceeds 190F (88C). This 
Limit Switch can be reset manually by pushing the button in the center of the switch which is located as 
shown.  

 

                                  

 

         

HEAT LIMIT SWITCH

 

 

 

 

 

 

 

 

 

THE HEAT LIMIT SWITCH CAN BE ACTIVATED IF THERE IS NOT A PROPER AMOUNT OF AIR 
FLOW BEING GENERATED BY THE COOLING FAN. IF THIS OCCURS: 

 
 

 

1.  DISCONNECT UNIT FROM POWER SOURCE. 

 
 

 

2.  Check to see if air intake area (openings in bottom center of Control Box) is free of dust, grease 

or other obstructions. 

 
 

 

3.  Check to see if Crumb Trays (heat reflectors) are in place.  

 
 

 

NEVER OPERATE UNIT WITHOUT CRUMB TRAYS IN POSITION AS THIS CAUSES 
OVERHEATING IN THE CONTROL BOX. 

 
 
 

             

CRUMB TRAY

CRUMB TRAY

 

 
 
TROUBLESHOOTING GUIDE CONT. ON PAGE 7 
 

 

 

 

 

 

 

 

 

REVISED 7/9/01 MJC 

 
 
 
 
 

Содержание MM14















Отзывы: