Hollis Prism 2 Скачать руководство пользователя страница 58

Страница: 58 / 67

Doc. 12-4091 - r01 (9/12/12)

PG-58

SERVICE

GUIDE

SUPPORT: TOLL-FREE 888-383-DIVE │ FAX 510-729-5115 │ E-MAIL [email protected]

2002 DESIGN

(

2012)

REASSEMBLY

NOTE: If the INTERNAL OVER-PRESSURE PLUG

(2) was still intact upon BATTERY HOUSING (1)

disassembly, skip step 1.

1. Ensure the plastic sealing surface is not damaged.

Then press the new

O-RING (3)

and

OVER-PRESSURE

PLUG (2)

into the port until fully seated with a dull instru-

ment (dental tool)

(Fig. 6)

2. Plug the

BATTERY CABLE ASSEMBLY (8)

into the

BULKHEAD CONNECTOR (7)

3. Fit the

FOAM INSERT (9)

into the

HOUSING (1)

4. Connect new batteries to the

BATTERY CABLE

ASSEMBLY (8)

. Then, ensuring that the wiring is not

twisted or contorted, place the batteries into the cutout in

the

FOAM INSERT (9)

NOTE: If the PRESSURE RELIEF VALVE (13) on

the LID (12) was not removed for replacement,

skip step 5.

5. Using a torque driver and 12 mm socket, tighten the

PRESSURE RELIEF VALVE ASSEMBLY (13)

clockwise

to a torque of 35 to 40 in/lbs (4 to 4.5 N-m)

(Fig. 7)

NOT

over-tighten.

6. Lightly lubricate and seat the

COMPARTMENT O-

RING (10)

in the groove of the

HOUSING (1)

, as shown

(Fig. 8)

7. Lightly lubricate and seat the

LID O-RING (11)

in the

groove of the

BATTERY LID (12)

, as shown.

8. Align the tabs of the

BATTERY LID (12)

. Then press

the

LID (12)

in place.

9. Engage and latch the two

RETAINING LATCHES (5)

(FIG. 9)

Fig. 6

Fig. 7

Fig. 8

Fig. 9

Содержание Prism 2




































































Результаты поиска

Содержание Prism 2

Отзывы:

Бренды по названию

Популярные бренды

Hollis Prism 2, Руководство пользователя и обслуживания

Результаты поиска

Содержание Prism 2

Отзывы:

Бренды по названию

Популярные бренды