background image

2

XL-DB20021UM-en-US · 2019-08-07 · Amendments and Errors Reserved · © SAF-HOLLAND, Inc., SAF-HOLLAND, HOLLAND, SAF, 

and logos are trademarks of SAF-HOLLAND S.A., SAF-HOLLAND GmbH, and SAF-HOLLAND, Inc.

Contents

Contents Page
Introduction ......................................................................... 2
Warranty .............................................................................. 2
Notes, Cautions, and Warnings ............................................. 2
Section 1 – General Safety Instructions ................................ 3
Section 2 – Welding Standards ............................................. 4
Exploded View and Parts List ................................................ 6  

Section 3 – Drawbar Eye Dimensions......... ........................... 7

Contents Page
Section 4 – Load Ratings ...................................................... 8
Section 5 – Towing Applications ........................................... 8
Section 6 – General Information......... .................................. 8
Section 7 – General Safety Information ................................ 8
Section 8 –  Mounting Instruction ......................................... 9
Section 9 – Operating Instructions ..................................... 12
Section 10 – Maintenance .................................................. 13

Introduction

This manual provides information necessary for the  
proper installation, operation and maintenance of the 
SAF-HOLLAND

®

 DB-090BW1 drawbar.

NOTE:

  For HOLLAND

®

 replacement components contact  

SAF-HOLLAND Customer Service at 1-888-396-6501.

Warranty

Refer to the complete warranty for the country in which  
the product will be used. A copy of the written warranty  
can be downloaded from our SAF-HOLLAND website  
(www.safholland.com).

Notes, Cautions, and Warnings

Read and understand all of the procedures presented in this 
manual before starting any work on the drawbar. 

NOTE:

  In the United States, work shop safety 

requirements are defined by federal and/or state 
Occupational Safety and Health Act. Equivalent 
laws could exist in other countries. This manual  
is written based on the assumption that OSHA  
or other applicable employee safety regulations  
are followed by the location where work  
is performed. 

Proper tools MUST be used to perform the mounting and 
maintenance procedures described in this manual.

This manual contains the terms “NOTE”, “IMPORTANT”, 
“CAUTION”, and “WARNING” followed by important product 
information. These terms are defined as follows:

NOTE:

  Includes additional information to enable 

accurate and easy performance of procedures.

IMPORTANT:

  Includes additional information that if  

NOT followed could lead to hindered 
product performance.

Used without the safety alert symbol, 
indicates a potentially hazardous 
situation which, if not avoided, could 
result in property damage.

Indicates a potentially hazardous 
situation which, if not avoided, could 
result in minor or moderate injury.

Indicates a potentially hazardous 
situation which, if not avoided, could 
result in death or serious injury.

Содержание DB-090BW1

















Отзывы: