background image

• 

9

TRAMPOLINE

Now lead the end of the line through the eyestrap on the rear of the front beam
and back through the loop. Lead the end back through the eyestrap and apply as
much tension as possible. Maintaining the tension, lead the line through the grom-
met and back to the eyestrap. Next, lead the line through the grommet in the front
edge of the trampoline and tie off securely. Repeat procedure for port side.

Move to the front right corner of
the trampoline. Pull on the line
as firmly as possible and tie a
bowline knot or loop in the line
as close to the trampoline edge
as possible. This will enable a
4:1 purchase to be used for ten-
sioning. Tie off once tensioned
to secure.

Tensioning the sides : starting at the right rear corner, take the
line that emerges from the trampoline. Lead it through the eye
strap on the rear beam and then through the grommet/eyelet.
Tie it off with a bowline knot or similar.

4

5

6

Retighten rear lacing from left to right. Tie the rear lacing off securely at the eyelet posts on the right hand end
of the rear beam. NB : 

         It is important that the trampoline lacing is kept very tight. Check the trampoline tension

on a regular basis. Remember : all ropes streches!

7

Содержание Twixxy



























Отзывы: