background image

• 

25

Hawaïan righting system

Take the shock cord supplied in the kit. Tie it with a tight knot onto the first ring supplied in the
kit. Pass the shock cord through the first pulley used in step 1, The shock cord passes then
through the eyelet at the center of the trampoline directly behind the mast step ball and back
into the eyelet of the trampoline. Then pass the shock cord through the second pulley used in
step 1 and tie it to the second ring supplied.

Tie the 2 small black pieces of rope onto the trampoline la-

cing at each end of the rear cross beam. To the other end of

each rope tie the small pulley supplied in the kit.

Take the righting rope (12 mm
yellow rope in the rope bag)
and pass it around the fixation
of the dolphin striker under the
front cross beam. Tie a knot in
the rope.

3

1

2

Named after the Hawaiian’s who are generally pretty relaxed people the Hawaiian righting system combines

safety, speed and comfort when righting your capsized catamaran.

Pass the rope through the first
ring, then around the dolphin
striker post in the center of the
front cross beam, then through
the second ring. Fix then this
rope to the dolphin striker on
the opposite side and secure
the rope.

4

From above

From below

Содержание Twixxy



























Отзывы: